Considering that street lamps are conductors, one way is major Street lamp high pole lamp Combination of external lightning protection and internal lightning protection. As the material of street lamp is conductor, it is equivalent to lightning rod, and downlead and grounding grid need to be installed in the design. These systems constitute the external lightning protection system. After the completion of the external lightning protection system, the fire and personal safety accidents caused by the direct lightning stroke of the street lamp can be avoided. After the completion of external lightning protection, the internal lightning protection system can protect the equipment by grounding and setting voltage protection. major Street lamp high pole lamp The internal lightning protection system is ready to prevent induced lightning and other forms of overvoltage intrusion, which may damage the power supply. This is also beyond the protection of external lightning protection system. Therefore, the built-in internal protection and external protection can complement each other.

The working voltage of a single bulb for LED tunnel lighting is very low, about 3V, so the power consumption of a low-voltage working environment is half of the power required for the same strong light. The tunnel lamp has a long service life and does not need regular maintenance and inspection. After a period of use, the traditional major Street lamp high pole lamp The brightness of the tunnel lamp will be greatly reduced, but its attenuation is only 20% of that of the tunnel lamp. Moreover, the tunnel lamp is small in size and can be made into various shapes to adapt to various environments. The shell of the tunnel lamp is of integrated design, which is durable and not easy to be damaged. Each light source inside can be installed and removed separately, which is very convenient in the future maintenance process, and the overall design can ensure good heat dissipation effect. The heat dissipation rack inside the shell, the airflow and the heat emitted by the full contact with the air, effectively reduce the major Street lamp high pole lamp And prolongs the service life of the tunnel lamp.

1. Shandong solar street lights will not go out suddenly: solar street lights use solar energy to absorb sunlight to charge batteries. When the weather is bad, the battery will provide power for the street lamp lighting, so the lamp will not be turned off suddenly. 2. Quality of LED light source: major Street lamp high pole lamp LED lamp cap is generally used as the light source of. Because LED lamp cap has many advantages, its lighting life is long, and it will not emit too much heat when used, which greatly extends the service life of the light source. 3. It can also be used normally in continuous rainy days: major Street lamp high pole lamp Solar energy is used to generate electricity, so they can usually be used for lighting on days without sunshine. Solar street lamp manufacturers will also consider these issues when designing solar street lamps, and then through communication with customers, according to the local rainy weather conditions of customers, they will configure appropriate street lamp accessories to solve most local problems.

1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Street lamp high pole lamp Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Street lamp high pole lamp engineering Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

The ultraviolet ray of LED energy-saving lamps is not particularly strong. major Street lamp high pole lamp It will not appear after using for a period of time. It may feel particularly strong and will not produce ultraviolet light, so it will not fade, will not be disturbed by mosquitoes, and the indoor sanitation can also become clean. major Street lamp high pole lamp It can also protect our eyes well. When starting, the time is faster, so it will not flash, so it can protect the eyes. The main advantage is that it can save power and has a longer service life. This is a good and reasonable guarantee. When you use it, you don't have to worry about life problems or abnormalities, nor about the cost of replacing the bulb. Moreover, when you use it, it is relatively robust and does not worry about frequent use. This would be bad.

major Street lamp high pole lamp Corresponding rules and regulations shall be formulated for construction, and construction personnel shall strictly abide by the rules and regulations. Follow the instructions of the on-site construction personnel and complete the production tasks together. Expressway safety slogans, warning signs, etc. shall be set around the buildings, and shall not be removed or moved at will. Their movement shall be approved by the on-site construction director. The installation height of lamps shall be consistent. Install according to the design requirements. major Street lamp high pole lamp The height of should be equal to the width of the road to be lit. Bench drills, toothless saws, cutting machines, etc., as well as electric tools for processing, need to be equipped with leakage protection devices. The elevation angle of the lamp is determined by the street width and light distribution curve of the lamp, and the elevation angle of each lamp needs to be the same. The place where resin glue and paint are stored shall be far away from fire sources, and sufficient fire-fighting equipment shall be placed.