The bulb shall be firm and upright and shall not be loose or skewed. If the enamel umbrella is corroded or deformed major Industrial lighting It needs to be replaced in time. Before using electric tools, please check whether the wiring, plug, socket, grounding and leakage protection devices are in good condition. Do not use them if they are damaged. Safety slogans, warning signs and safety operation instruction boards shall be set up on the construction site. Materials on the site shall be stacked orderly and stably and handled from top to bottom. When using hand-held electric tools, please wear personal protective equipment and the power cord should be empty. It is forbidden for non operators to use it on site major Industrial lighting Power switches, wires and various mechanical equipment. Outdoor construction is not allowed in rainy season. Outdoor construction should be carried out after the rain is dry. The Quality Safety Department is responsible for preparing labor protection articles to ensure the safety of construction personnel.

one major Industrial lighting The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Industrial lighting The use of crystal oscillator time control can make the time control more accurate.

1. Lamp holder: it needs to be sealed through the lamp holder. major Industrial lighting The waterproof treatment of lamp cap can ensure the service life of street lamp. Therefore, the selection of street lamp housing is very important. 2. Controller: when selecting, pay attention to whether the style is waterproof. When installing the controller, it is usually placed in the road to better avoid wind and sun exposure. 3. Battery: it needs to have certain waterproof performance. In order to install the battery, please bury the battery about 40cm underground to avoid flooding. After that, test major Industrial lighting Head to check whether the street lamp lights up normally. If it is opened, it can be used normally; otherwise, it needs to be replaced. Light poles need to be hot-dip galvanized to ensure smooth surface, no color difference, no pinholes, and no skin peeling after use.

The working voltage of a single bulb for LED tunnel lighting is very low, about 3V, so the power consumption of a low-voltage working environment is half of the power required for the same strong light. The tunnel lamp has a long service life and does not need regular maintenance and inspection. After a period of use, the traditional major Industrial lighting The brightness of the tunnel lamp will be greatly reduced, but its attenuation is only 20% of that of the tunnel lamp. Moreover, the tunnel lamp is small in size and can be made into various shapes to adapt to various environments. The shell of the tunnel lamp is of integrated design, which is durable and not easy to be damaged. Each light source inside can be installed and removed separately, which is very convenient in the future maintenance process, and the overall design can ensure good heat dissipation effect. The heat dissipation rack inside the shell, the airflow and the heat emitted by the full contact with the air, effectively reduce the major Industrial lighting And prolongs the service life of the tunnel lamp.

At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Industrial lighting Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Industrial lighting It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Industrial lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Industrial lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.