1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Municipal lighting Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Municipal lighting manufactor Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

First, we need to observe major Municipal lighting The workmanship of the mask and its luminous effect. This depends on how much light the bulb lamp shade emits to the light source. When viewing the mask, you can view its shape, whether the light transmittance and thickness of the bulb are the same, and check the approximate blur of the mask. We need to see if the material of the bulb is suitable for heat conduction. You can test in the field. After working for several minutes, observe whether there is odor above the bulb when the temperature rises. After that, we will also check the lamp body temperature after the power is turned off. The lower the temperature, the better. ordinary major Municipal lighting It will change due to the change of ambient temperature. When selecting bulb lamp, you need to check its color temperature. Generally speaking, the color temperature should not be too high or too low as long as it can meet the normal household lighting needs.

Main pole of high pole lamp: major Municipal lighting When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Municipal lighting If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.

How to reduce the risk of theft of Shandong solar street lights? Lanyue Optoelectronics Co., Ltd. recommends that you take the following measures: (1) major Municipal lighting Its cost is higher than that of traditional street lamp poles, and its anti-theft and stability technology is not mature enough. They should be installed in public places or relatively safe places in cities. It is not easy to install them in suburbs; (2) Among all the components, the battery is the part that is easy to be stolen. Therefore, we can bury the battery underground, under the building as far as possible, and then pour it in with cement, which can achieve good results. Anti-theft effect; (3) Attach importance to major Municipal lighting Security monitoring, establish monitoring systems or install alarm systems in places prone to theft, timely understand the use of solar street lights, and carry out effective management;

If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Municipal lighting The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Municipal lighting The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Municipal lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Municipal lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.