Main pole of high pole lamp: major Solar Garden Light When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Solar Garden Light If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.
The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Solar Garden Light It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. The installation position of the floodlight shall be able to bear the weight of the floodlight, and its bearing capacity shall be greater than major Solar Garden Light 10 times the weight, so that the lamp can be firmly installed and avoid the risk of falling in the future.
1. High purity aluminum reflector, accurate beam and good reflection effect. 2. Symmetrical narrow angle, wide angle and asymmetric light distribution system. 3. The rear open bulb can be replaced, which is easy to maintain. 4. The lamp is equipped with a dial to adjust the lighting angle. major Solar Garden Light Controlled by the built-in microchip. In small engineering applications, it can be used without a controller, and can achieve gradual change, jump, color flicker, random flicker. DMX can also control dynamic effects such as gradients to achieve effects such as chasing and scanning. Its main application places may be: single building, exterior wall lighting of historical buildings, interior and exterior lighting of buildings, interior local lighting, green landscape lighting, billboard lighting, medical culture and other professional facilities lighting, bars, dance halls and other entertainment places major Solar Garden Light 。
one major Solar Garden Light The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Solar Garden Light The use of crystal oscillator time control can make the time control more accurate.
(1) There are potential safety hazards in municipal lighting: due to the construction quality, garden engineering transformation, aging materials, abnormal power supply, water and electricity pipeline conflict, many potential safety hazards have been brought. (2) Solar street lamps are energy-saving and environment-friendly new energy power generation products. There is no electricity bill. High electricity charge for mains lighting: major Solar Garden Light Our jobs have fixed and high electricity bills. Solar lighting is free of electricity charge: solar road lighting is a one-time investment without any maintenance costs, the investment cost can be recovered within three years, and has long-term benefits. （3） major Solar Garden Light The installation of the solar street lamp is very simple: when installing the solar street lamp, you don't need to lay complex lines, just make a cement base and fix it with stainless steel screws. The installation of municipal lighting fixtures is very complicated: there are complex operating procedures in the municipal lighting project.
When the solar street lamp leaves the factory, the working time is generally set according to the customer's requirements. major Solar Garden Light The start and stop time of is determined by the street lamp controller. Most of the controllers are installed inside the light door, while most of the lithium battery storage and control integrated machines produced by our company are installed at the bottom of the solar panel. Controller adjustment is divided into manual adjustment and remote control adjustment. The external adjustment button can be adjusted manually. However, most of the current markets are remote control adjustment. This type of controller needs to be equipped with a remote control to adjust the working time. How to adjust major Solar Garden Light The time of also depends on the type of controller used.
