The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Smart street lamp It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Smart street lamp Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.

LED panel light is a point shaped illuminant, which brings creative visual effects through the flexible design of points, lines and surfaces. It is light and thin, and can be installed on the ceiling, wall and the surface of the installation body, and suspended under the ceiling or the installation body. According to customer requirements, we can design light sources with different shapes and particles, which are flexible in design. High brightness major Smart street lamp Light source, quick start, natural and soft light. It belongs to the category of lamps with strong anti vibration ability. The light source is a high hardness resin illuminant rather than tungsten glass, which is not easy to be damaged. Therefore, it has high anti vibration ability and strong adaptability to ambient temperature. major Smart street lamp The uniform luminous reflective plate and sealed internal design are adopted, which are combined with the light guide plate and made of aluminum alloy materials. The effect is uniform and the lighting range is larger.

1. Be able to monitor the temperature of the light source chip pad of the street lamp itself or the temperature of the lamp shell and conduct fault diagnosis; 2. Remote measurement of electrical parameters such as street lamp current and voltage, remote switching of street lamps, remote viewing of on-site operation of important road sections, etc; 3. According to major Smart street lamp The monitoring data of can timely grasp the abnormal position and reason of street lights, and carry out purposeful maintenance without having to go to the whole city for inspection, which speeds up the speed. 4. It has daylight sensor or on-board sensor dimming, energy saving control, time control and even RTC dimming; 5. In some areas with few people and vehicles, it can be controlled at half bright time in the middle of the night, but when people and cars pass by, major Smart street lamp They will reach the distance ahead and in a few cases restore the original brightness. Seconds. 6. The lighting standard level of the same road will change with time and traffic flow.

During use, the bulb will be hit by wind and rain, which may cause its angle deviation, thus affecting the lighting effect. If any deviation is found, it must be adjusted in time. Check the bulb surface regularly. If on major Smart street lamp Cracks found on the surface glass of the bulb may cause rainwater to enter the bulb, which will seriously affect the use effect and service life of the bulb. The bulb should be removed immediately and sent to the original factory for repair. Avoid all kinds of serious accidents, such as leakage. Clean the lamp regularly to maintain its brightness. Turn off the lamp before cleaning it major Smart street lamp The power supply of the lamp shall be cleaned with a dry cloth or dry cloth to prevent the lamp from being damp, let alone with chemical or corrosive substances. Otherwise, the bulb will be corroded, which may cause accidents.

Main pole of high pole lamp: major Smart street lamp When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Smart street lamp If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.

Considering that street lamps are conductors, one way is major Smart street lamp Combination of external lightning protection and internal lightning protection. As the material of street lamp is conductor, it is equivalent to lightning rod, and downlead and grounding grid need to be installed in the design. These systems constitute the external lightning protection system. After the completion of the external lightning protection system, the fire and personal safety accidents caused by the direct lightning stroke of the street lamp can be avoided. After the completion of external lightning protection, the internal lightning protection system can protect the equipment by grounding and setting voltage protection. major Smart street lamp The internal lightning protection system is ready to prevent induced lightning and other forms of overvoltage intrusion, which may damage the power supply. This is also beyond the protection of external lightning protection system. Therefore, the built-in internal protection and external protection can complement each other.