1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Street lamp high pole lamp Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Street lamp high pole lamp Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

(1) Solar panel: 18v, 30-240wp monocrystalline silicon or polycrystalline silicon; (2) Controller: major Street lamp high pole lamp Intelligent controller; (3) Battery: DC12V, 24V, lead-acid battery or gel battery, maintenance free; (4) Light source type: high-power LED integrated lamp head, die-casting aluminum material; (5) Light source power: 20-60W; (6) Light pole material: steel structure, hot-dip galvanizing, plastic spraying treatment; (7) Height: 6-8m; (8) Working time: 5-12 hours, 4-5 days in rainy days (different sunshine time in different regions); (9) Working temperature: - 35 ℃ - 65 ℃; In addition, major Street lamp high pole lamp For the selection of solar panels and batteries, please refer to the purchase notes of solar street lamps. It can be seen that the selection of proper garden lamps is not only reasonable in price, but also comprehensive. In order to avoid unnecessary troubles.

When the solar street lamp leaves the factory, the working time is generally set according to the customer's requirements. major Street lamp high pole lamp The start and stop time of is determined by the street lamp controller. Most of the controllers are installed inside the light door, while most of the lithium battery storage and control integrated machines produced by our company are installed at the bottom of the solar panel. Controller adjustment is divided into manual adjustment and remote control adjustment. The external adjustment button can be adjusted manually. However, most of the current markets are remote control adjustment. This type of controller needs to be equipped with a remote control to adjust the working time. How to adjust major Street lamp high pole lamp The time of also depends on the type of controller used.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Street lamp high pole lamp Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Street lamp high pole lamp To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.

The life of LED mining lamp depends largely on the level of heat dissipation, and the main way to improve the level of heat dissipation is to transfer the excess heat generated by the chip through the radiator and radiator. At the same time, major Street lamp high pole lamp The main parameters related to LED heat dissipation are thermal resistance, junction temperature, temperature rise, etc. Thermal resistance is the quotient obtained by dividing the difference between the effective temperature of the equipment and the temperature of the external designated reference point by the steady-state power consumption in the equipment. It is an important parameter indicating the degree of heat dissipation of equipment. Junction temperature refers to the temperature of the semiconductor junction of the main heating part in the LED device. It reflects major Street lamp high pole lamp Temperature value that can be withstood under working conditions. Temperature rise refers to the temperature rise of the enclosure environment. It refers to the difference between the temperature of LED equipment shell and the ambient temperature. This is a temperature value that can be directly measured, which can directly reflect the heat dissipation degree around LED devices.

1: Environment friendly lamp. LED products do not contain lead and other harmful substances, and the shell can also be recycled, which is harmless to the environment. 2: Fever is low. No UV, 3: no noise. LED light will not produce noise, so it is a good choice for occasions where quasi dense electronic instruments are used. 4: Protect eyes. major Street lamp high pole lamp LED constant current operation can effectively reduce LED light attenuation, start quickly, no flicker and protect eyes. 5: There is no trouble of mosquitoes, no harmful substances such as mercury, and less heat generated. 6: Wide voltage range. LED lights can be lit within a certain voltage range. 7: Power saving and long service life. It can be used for a long time without replacement, which reduces the labor cost. 8: Firm and reliable. major Street lamp high pole lamp It uses epoxy resin instead of traditional glass. 9: The appearance and size of multi-functional LED lamps are the same as those of traditional fluorescent lamps, which can replace traditional fluorescent lamps. 10: Rich color makes full use of the rich color of LED to make a variety of light emitting colors.