With the emergence of high brightness white LED light source, it is possible to apply it in the lighting field. According to the prediction of international authoritative organizations, the 21st century will enter the era of new light sources represented by LED, that is, the fourth generation of new light sources. major Industrial lighting Its brightness is the same as that of traditional fluorescent lamps, and its color is gentle and easy to accept. The service life is 50000-80000 hours. When the bulb is started, it will open immediately and can be repaired when it is damaged (the traditional fluorescent lamp has been damaged and cannot be reused). It is not only very energy-saving, but also more environmentally friendly. major Industrial lighting It is one of the main products promoted by the national green lighting energy-saving project, and is currently the first choice to replace the traditional high-pressure sodium lamp for industrial and mining lamps. At present, LED mining lamp has been used in many industrial enterprises, and its application effect is well received by customers.

1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Industrial lighting The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Industrial lighting The general trend of. There is a lot to do.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Industrial lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Industrial lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

(1) Recommended installation height of 50W LED energy-saving mining lamp: 3-5 meters; Installation distance: 5-8m. (2) Recommended installation height of 100W LED energy-saving mining lamp: 6-8m; Installation distance: 8-10 m. (3) 120W LED energy-saving mining lamp Recommended installation height: 8-10m; Installation distance: 8-10 m. （4）150W major Industrial lighting Recommended installation height: 10-15m; Installation distance: 8-12m. （5） major Industrial lighting 200W Recommended installation height: 10-15m; Installation distance: 10-15m. (6) LED energy-saving mining lamp 300W recommended installation height: 15-20m; Installation distance: 20-25m. (7) Recommended installation height of 450W LED energy-saving mining lamp: 15-20m; Installation distance: 25-30m

When the solar street lamp leaves the factory, the working time is generally set according to the customer's requirements. major Industrial lighting The start and stop time of is determined by the street lamp controller. Most of the controllers are installed inside the light door, while most of the lithium battery storage and control integrated machines produced by our company are installed at the bottom of the solar panel. Controller adjustment is divided into manual adjustment and remote control adjustment. The external adjustment button can be adjusted manually. However, most of the current markets are remote control adjustment. This type of controller needs to be equipped with a remote control to adjust the working time. How to adjust major Industrial lighting The time of also depends on the type of controller used.

1. Shandong solar street lights will not go out suddenly: solar street lights use solar energy to absorb sunlight to charge batteries. When the weather is bad, the battery will provide power for the street lamp lighting, so the lamp will not be turned off suddenly. 2. Quality of LED light source: major Industrial lighting LED lamp cap is generally used as the light source of. Because LED lamp cap has many advantages, its lighting life is long, and it will not emit too much heat when used, which greatly extends the service life of the light source. 3. It can also be used normally in continuous rainy days: major Industrial lighting Solar energy is used to generate electricity, so they can usually be used for lighting on days without sunshine. Solar street lamp manufacturers will also consider these issues when designing solar street lamps, and then through communication with customers, according to the local rainy weather conditions of customers, they will configure appropriate street lamp accessories to solve most local problems.