1、 Disconnection. For "dead light", we should first determine major Industrial lighting Is it short circuit or open circuit. 2、 The adhesive layer is peeled off. For some LED energy-saving project lights with vertical chips, the common reasons for dead lights are the peeling off of the bottom of the chip bonding layer and the peeling off of the bracket coating. 3、 The welding spot is burnt. In some cases, the dead light of the bulb may not be caused by the bulb itself, but also by the power supply used. 4、 Chip corrosion. The previous energy-saving floodlights and energy-saving floodlights are open circuit. The following is the condition of short circuit dead light. major Industrial lighting There are many reasons for dead lights. Dead light may appear in every link from packaging, application to use.

major Industrial lighting Corresponding rules and regulations shall be formulated for construction, and construction personnel shall strictly abide by the rules and regulations. Follow the instructions of the on-site construction personnel and complete the production tasks together. Expressway safety slogans, warning signs, etc. shall be set around the buildings, and shall not be removed or moved at will. Their movement shall be approved by the on-site construction director. The installation height of lamps shall be consistent. Install according to the design requirements. major Industrial lighting The height of should be equal to the width of the road to be lit. Bench drills, toothless saws, cutting machines, etc., as well as electric tools for processing, need to be equipped with leakage protection devices. The elevation angle of the lamp is determined by the street width and light distribution curve of the lamp, and the elevation angle of each lamp needs to be the same. The place where resin glue and paint are stored shall be far away from fire sources, and sufficient fire-fighting equipment shall be placed.

The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Industrial lighting It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Industrial lighting Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.

If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Industrial lighting The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Industrial lighting The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.

1. Quality assurance, green and environmental protection, our LED lamp has a long life, low light attenuation and high brightness. They are the first choice for energy-saving transformation of factories. 2. Energy saving. The service life of Danohangpu LED products can reach 50000 hours, and the energy-saving effect is 40% - 60% of that of ordinary lamps, greatly reducing the power consumption. 3. Professional major Industrial lighting Plan and plan. Make a reasonable lighting configuration plan according to the width of the road and the lighting time of the area, so that you will not waste money and reasonably configure the light source. 4. Professional technical guidance and after-sales service, professional technical team major Industrial lighting We provide on-site technical guidance and problem solving for the installation and transformation of. Perfect after-sales service is our intimate guarantee for users. 5. From the manufacturer to the manufacturer, shorten the intermediate link, and directly solve the problem that dealers do not understand the technology and the price is slightly higher from the manufacturer's plan - product customization - product inspection - product delivery - manufacturer acceptance, and one-stop service.