If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Plant lighting The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Plant lighting The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.

one major Plant lighting The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Plant lighting The use of crystal oscillator time control can make the time control more accurate.

When the solar street lamp leaves the factory, the working time is generally set according to the customer's requirements. major Plant lighting The start and stop time of is determined by the street lamp controller. Most of the controllers are installed inside the light door, while most of the lithium battery storage and control integrated machines produced by our company are installed at the bottom of the solar panel. Controller adjustment is divided into manual adjustment and remote control adjustment. The external adjustment button can be adjusted manually. However, most of the current markets are remote control adjustment. This type of controller needs to be equipped with a remote control to adjust the working time. How to adjust major Plant lighting The time of also depends on the type of controller used.

fixed major Plant lighting There are many methods, such as ceiling, embedded, hoisting (straight pipe or chain) and wall absorption. Generally, open lamps are usually used indoors. Enamel surface reflector shall be selected, with thick aluminum oxide film or aluminum reflector coated with silicon dioxide protective film. Movable local illuminators are equipped with corresponding handles, hooks, clamps, etc. Fixed local illuminators are usually firmly locked on the working machine by screws or fixing mechanisms. For large factories and large machine tool places requiring separate lighting major Plant lighting Reflectors made of materials with strong light control characteristics, such as prismatic glass, mirror glass and polished aluminum, to obtain narrow beam distribution.

1、 Good corporate culture and elite team. If you want to occupy the market in the competition of the same industry, you need to have an outstanding team. Talent introduction and corporate culture play a very important role. Market competition is team competition. The formation of an elite team needs the support of a good corporate culture. 2、 Verify the status quo and launch luxury products and flagship products. Under the current national policy, environmental protection has become the key point of national governance. Introduction of environment-friendly major Plant lighting It has become the current development trend of all enterprises. 3、 The price of good quality and good after-sales service products depends on the quality. Only good product quality can lead to good price. As a service industry, good major Plant lighting After sales service is also very important. If the after-sales service is good, we can retain old customers and develop new customers. As long as there are customers, there is a market for products. Quality is always one.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Plant lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Plant lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.