1. Energy saving economy. First, each solar street lamp is a relatively independent system. In the process of installation and construction, there is no need to lay cables or dig roads, thus saving a lot of manpower, material resources and installation costs; In addition, it also consumes electricity, and ordinary street lights are on all day. The lamp lasts about 6 hours, consumes about 2 kWh, and the annual electricity charge is more than 300 yuan. According to 300 street lights in the urban area, the annual cost is nearly 100000 yuan. Can be saved major Intelligent factory lighting 。 2. Energy conservation and environmental protection. Kaifeng major Intelligent factory lighting It is mainly composed of four departments: photovoltaic module, light-emitting diode, solar cell and controller. Photovoltaic modules absorb light in the daytime, convert solar energy into electric energy, store it in solar cells, and release illumination when it turns dark at night.

1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Intelligent factory lighting Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Intelligent factory lighting engineering Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

During use, the bulb will be hit by wind and rain, which may cause its angle deviation, thus affecting the lighting effect. If any deviation is found, it must be adjusted in time. Check the bulb surface regularly. If on major Intelligent factory lighting Cracks found on the surface glass of the bulb may cause rainwater to enter the bulb, which will seriously affect the use effect and service life of the bulb. The bulb should be removed immediately and sent to the original factory for repair. Avoid all kinds of serious accidents, such as leakage. Clean the lamp regularly to maintain its brightness. Turn off the lamp before cleaning it major Intelligent factory lighting The power supply of the lamp shall be cleaned with a dry cloth or dry cloth to prevent the lamp from being damp, let alone with chemical or corrosive substances. Otherwise, the bulb will be corroded, which may cause accidents.

The working voltage of a single bulb for LED tunnel lighting is very low, about 3V, so the power consumption of a low-voltage working environment is half of the power required for the same strong light. The tunnel lamp has a long service life and does not need regular maintenance and inspection. After a period of use, the traditional major Intelligent factory lighting The brightness of the tunnel lamp will be greatly reduced, but its attenuation is only 20% of that of the tunnel lamp. Moreover, the tunnel lamp is small in size and can be made into various shapes to adapt to various environments. The shell of the tunnel lamp is of integrated design, which is durable and not easy to be damaged. Each light source inside can be installed and removed separately, which is very convenient in the future maintenance process, and the overall design can ensure good heat dissipation effect. The heat dissipation rack inside the shell, the airflow and the heat emitted by the full contact with the air, effectively reduce the major Intelligent factory lighting And prolongs the service life of the tunnel lamp.

1: Environment friendly lamp. LED products do not contain lead and other harmful substances, and the shell can also be recycled, which is harmless to the environment. 2: Fever is low. No UV, 3: no noise. LED light will not produce noise, so it is a good choice for occasions where quasi dense electronic instruments are used. 4: Protect eyes. major Intelligent factory lighting LED constant current operation can effectively reduce LED light attenuation, start quickly, no flicker and protect eyes. 5: There is no trouble of mosquitoes, no harmful substances such as mercury, and less heat generated. 6: Wide voltage range. LED lights can be lit within a certain voltage range. 7: Power saving and long service life. It can be used for a long time without replacement, which reduces the labor cost. 8: Firm and reliable. major Intelligent factory lighting It uses epoxy resin instead of traditional glass. 9: The appearance and size of multi-functional LED lamps are the same as those of traditional fluorescent lamps, which can replace traditional fluorescent lamps. 10: Rich color makes full use of the rich color of LED to make a variety of light emitting colors.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Intelligent factory lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Intelligent factory lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.