1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Plant lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Plant lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.

Main pole of high pole lamp: major Plant lighting When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Plant lighting If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.

(1) Recommended installation height of 50W LED energy-saving mining lamp: 3-5 meters; Installation distance: 5-8m. (2) Recommended installation height of 100W LED energy-saving mining lamp: 6-8m; Installation distance: 8-10 m. (3) 120W LED energy-saving mining lamp Recommended installation height: 8-10m; Installation distance: 8-10 m. （4）150W major Plant lighting Recommended installation height: 10-15m; Installation distance: 8-12m. （5） major Plant lighting 200W Recommended installation height: 10-15m; Installation distance: 10-15m. (6) LED energy-saving mining lamp 300W recommended installation height: 15-20m; Installation distance: 20-25m. (7) Recommended installation height of 450W LED energy-saving mining lamp: 15-20m; Installation distance: 25-30m

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Plant lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Plant lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

With the emergence of high brightness white LED light source, it is possible to apply it in the lighting field. According to the prediction of international authoritative organizations, the 21st century will enter the era of new light sources represented by LED, that is, the fourth generation of new light sources. major Plant lighting Its brightness is the same as that of traditional fluorescent lamps, and its color is gentle and easy to accept. The service life is 50000-80000 hours. When the bulb is started, it will open immediately and can be repaired when it is damaged (the traditional fluorescent lamp has been damaged and cannot be reused). It is not only very energy-saving, but also more environmentally friendly. major Plant lighting It is one of the main products promoted by the national green lighting energy-saving project, and is currently the first choice to replace the traditional high-pressure sodium lamp for industrial and mining lamps. At present, LED mining lamp has been used in many industrial enterprises, and its application effect is well received by customers.