1. Energy saving economy. First, each solar street lamp is a relatively independent system. In the process of installation and construction, there is no need to lay cables or dig roads, thus saving a lot of manpower, material resources and installation costs; In addition, it also consumes electricity, and ordinary street lights are on all day. The lamp lasts about 6 hours, consumes about 2 kWh, and the annual electricity charge is more than 300 yuan. According to 300 street lights in the urban area, the annual cost is nearly 100000 yuan. Can be saved major Rural lighting 。 2. Energy conservation and environmental protection. Jining major Rural lighting It is mainly composed of four departments: photovoltaic module, light-emitting diode, solar cell and controller. Photovoltaic modules absorb light in the daytime, convert solar energy into electric energy, store it in solar cells, and release illumination when it turns dark at night.

Like the hump of a camel, the battery of a solar street lamp has the function of storing energy. The importance is self-evident. Third generation solar street lamp battery replacement, from lead-acid battery to gel battery to lithium battery. At present, the mainstream major Rural lighting Battery has gradually developed from gel battery to lithium battery. Relatively speaking, colloidal battery has low price, relatively mature technology and high stability. advantage. The disadvantages are that compared with lithium batteries of the same level, the service life is relatively short, the electric energy storage capacity of the same volume is less, and there are other fatal disadvantages. Although the apparent price is a little expensive, the use cost is very low. Two years of poor use, we major Rural lighting engineering The battery pack can be used for 8-10 years. Welcome new and old customers to call and write.

The life of LED mining lamp depends largely on the level of heat dissipation, and the main way to improve the level of heat dissipation is to transfer the excess heat generated by the chip through the radiator and radiator. At the same time, major Rural lighting The main parameters related to LED heat dissipation are thermal resistance, junction temperature, temperature rise, etc. Thermal resistance is the quotient obtained by dividing the difference between the effective temperature of the equipment and the temperature of the external designated reference point by the steady-state power consumption in the equipment. It is an important parameter indicating the degree of heat dissipation of equipment. Junction temperature refers to the temperature of the semiconductor junction of the main heating part in the LED device. It reflects major Rural lighting Temperature value that can be withstood under working conditions. Temperature rise refers to the temperature rise of the enclosure environment. It refers to the difference between the temperature of LED equipment shell and the ambient temperature. This is a temperature value that can be directly measured, which can directly reflect the heat dissipation degree around LED devices.

If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Rural lighting The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Rural lighting The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Rural lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Rural lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.

major Rural lighting Corresponding rules and regulations shall be formulated for construction, and construction personnel shall strictly abide by the rules and regulations. Follow the instructions of the on-site construction personnel and complete the production tasks together. Expressway safety slogans, warning signs, etc. shall be set around the buildings, and shall not be removed or moved at will. Their movement shall be approved by the on-site construction director. The installation height of lamps shall be consistent. Install according to the design requirements. major Rural lighting The height of should be equal to the width of the road to be lit. Bench drills, toothless saws, cutting machines, etc., as well as electric tools for processing, need to be equipped with leakage protection devices. The elevation angle of the lamp is determined by the street width and light distribution curve of the lamp, and the elevation angle of each lamp needs to be the same. The place where resin glue and paint are stored shall be far away from fire sources, and sufficient fire-fighting equipment shall be placed.