If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Factory chandelier The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Factory chandelier The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.
Considering that street lamps are conductors, one way is major Factory chandelier Combination of external lightning protection and internal lightning protection. As the material of street lamp is conductor, it is equivalent to lightning rod, and downlead and grounding grid need to be installed in the design. These systems constitute the external lightning protection system. After the completion of the external lightning protection system, the fire and personal safety accidents caused by the direct lightning stroke of the street lamp can be avoided. After the completion of external lightning protection, the internal lightning protection system can protect the equipment by grounding and setting voltage protection. major Factory chandelier The internal lightning protection system is ready to prevent induced lightning and other forms of overvoltage intrusion, which may damage the power supply. This is also beyond the protection of external lightning protection system. Therefore, the built-in internal protection and external protection can complement each other.
LED garden lights are energy-saving and environmentally friendly. The main structure is an electroluminescent semiconductor diode, which has low luminous flux loss and long service life. According to the scientific research results of LED light source, major Factory chandelier Its service life is three times that of the basic light source and 30% that of the energy-saving street lamp. Power saving is equal to saving the investment in electricity costs, and it is also because LED courtyard lamps have their unique advantages, which can meet the requirements of today's society for energy conservation and environmental protection. courtyard major Factory chandelier The advantage of saving more electricity costs has a wide influence on the market. In order to improve people's quality of life, the street lamps that need to be used are energy-saving and environmentally friendly. Both specifications, lighting performance and lighting effect can meet the requirements of street lamp standards. Facing many LED garden lights with complex market environment, it is necessary to choose a good brand LED garden light manufacturer.
1、 Disconnection. For "dead light", we should first determine major Factory chandelier Is it short circuit or open circuit. 2、 The adhesive layer is peeled off. For some LED energy-saving project lights with vertical chips, the common reasons for dead lights are the peeling off of the bottom of the chip bonding layer and the peeling off of the bracket coating. 3、 The welding spot is burnt. In some cases, the dead light of the bulb may not be caused by the bulb itself, but also by the power supply used. 4、 Chip corrosion. The previous energy-saving floodlights and energy-saving floodlights are open circuit. The following is the condition of short circuit dead light. major Factory chandelier There are many reasons for dead lights. Dead light may appear in every link from packaging, application to use.
Main pole of high pole lamp: major Factory chandelier When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Factory chandelier If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.
(1) Recommended installation height of 50W LED energy-saving mining lamp: 3-5 meters; Installation distance: 5-8m. (2) Recommended installation height of 100W LED energy-saving mining lamp: 6-8m; Installation distance: 8-10 m. (3) 120W LED energy-saving mining lamp Recommended installation height: 8-10m; Installation distance: 8-10 m. （4）150W major Factory chandelier Recommended installation height: 10-15m; Installation distance: 8-12m. （5） major Factory chandelier 200W Recommended installation height: 10-15m; Installation distance: 10-15m. (6) LED energy-saving mining lamp 300W recommended installation height: 15-20m; Installation distance: 20-25m. (7) Recommended installation height of 450W LED energy-saving mining lamp: 15-20m; Installation distance: 25-30m
