LED panel light is a point shaped illuminant, which brings creative visual effects through the flexible design of points, lines and surfaces. It is light and thin, and can be installed on the ceiling, wall and the surface of the installation body, and suspended under the ceiling or the installation body. According to customer requirements, we can design light sources with different shapes and particles, which are flexible in design. High brightness major City circuit lamp Light source, quick start, natural and soft light. It belongs to the category of lamps with strong anti vibration ability. The light source is a high hardness resin illuminant rather than tungsten glass, which is not easy to be damaged. Therefore, it has high anti vibration ability and strong adaptability to ambient temperature. major City circuit lamp The uniform luminous reflective plate and sealed internal design are adopted, which are combined with the light guide plate and made of aluminum alloy materials. The effect is uniform and the lighting range is larger.

Like the hump of a camel, the battery of a solar street lamp has the function of storing energy. The importance is self-evident. Third generation solar street lamp battery replacement, from lead-acid battery to gel battery to lithium battery. At present, the mainstream major City circuit lamp Battery has gradually developed from gel battery to lithium battery. Relatively speaking, colloidal battery has low price, relatively mature technology and high stability. advantage. The disadvantages are that compared with lithium batteries of the same level, the service life is relatively short, the electric energy storage capacity of the same volume is less, and there are other fatal disadvantages. Although the apparent price is a little expensive, the use cost is very low. Two years of poor use, we major City circuit lamp manufactor The battery pack can be used for 8-10 years. Welcome new and old customers to call and write.

1. High purity aluminum reflector, accurate beam and good reflection effect. 2. Symmetrical narrow angle, wide angle and asymmetric light distribution system. 3. The rear open bulb can be replaced, which is easy to maintain. 4. The lamp is equipped with a dial to adjust the lighting angle. major City circuit lamp Controlled by the built-in microchip. In small engineering applications, it can be used without a controller, and can achieve gradual change, jump, color flicker, random flicker. DMX can also control dynamic effects such as gradients to achieve effects such as chasing and scanning. Its main application places may be: single building, exterior wall lighting of historical buildings, interior and exterior lighting of buildings, interior local lighting, green landscape lighting, billboard lighting, medical culture and other professional facilities lighting, bars, dance halls and other entertainment places major City circuit lamp 。

If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major City circuit lamp The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major City circuit lamp The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.

install major City circuit lamp The construction site shall be provided with safety slogans, warning signs and safety operation instruction boards, which shall not be removed or moved at will. Any movement shall be approved by the person in charge of site construction. When working on site, please pay attention to vehicle access and mechanical lifting. During normal construction, there should be no less than 2 people, and when there is only one person on site, no operation is allowed. Obey the instructions of on-site construction personnel, obey the assignment, unite and complete the production task. Materials on site shall be stacked neatly, and hazardous materials, chemical reagents and flammable materials must be placed separately. It is strictly prohibited to work in flammable and explosive places, open fire, smoking, etc. In operation major City circuit lamp Before that, please check whether the operation site is safe, whether the road is unblocked and whether the protective measures are complete. The tools used should be restored after the work is completed. Please wear safety belt when working at heights, cliffs and steep slopes without protective facilities.