The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Factory chandelier It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Factory chandelier Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.

Main pole of high pole lamp: major Factory chandelier When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Factory chandelier If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.

1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Factory chandelier The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Factory chandelier The general trend of. There is a lot to do.

fixed major Factory chandelier There are many methods, such as ceiling, embedded, hoisting (straight pipe or chain) and wall absorption. Generally, open lamps are usually used indoors. Enamel surface reflector shall be selected, with thick aluminum oxide film or aluminum reflector coated with silicon dioxide protective film. Movable local illuminators are equipped with corresponding handles, hooks, clamps, etc. Fixed local illuminators are usually firmly locked on the working machine by screws or fixing mechanisms. For large factories and large machine tool places requiring separate lighting major Factory chandelier Reflectors made of materials with strong light control characteristics, such as prismatic glass, mirror glass and polished aluminum, to obtain narrow beam distribution.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Factory chandelier Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Factory chandelier Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.