LED panel light is a point shaped illuminant, which brings creative visual effects through the flexible design of points, lines and surfaces. It is light and thin, and can be installed on the ceiling, wall and the surface of the installation body, and suspended under the ceiling or the installation body. According to customer requirements, we can design light sources with different shapes and particles, which are flexible in design. High brightness major Plant light Light source, quick start, natural and soft light. It belongs to the category of lamps with strong anti vibration ability. The light source is a high hardness resin illuminant rather than tungsten glass, which is not easy to be damaged. Therefore, it has high anti vibration ability and strong adaptability to ambient temperature. major Plant light The uniform luminous reflective plate and sealed internal design are adopted, which are combined with the light guide plate and made of aluminum alloy materials. The effect is uniform and the lighting range is larger.
The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Plant light It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Plant light Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.
(1) High light efficiency: the spectrum is almost all concentrated on the visible light frequency, and the efficiency can reach 80% - 90%. (2) High light quality: because there is no ultraviolet and infrared ray in the spectrum, there is no heat and radiation. This is a typical green light source. (3) Long life: the standard life is 40000 hours when the luminous flux decays to 70%. major Plant light It can be used for 8 years under normal conditions. (4) Reliable and durable: there is no tungsten wire, glass and other easily damaged parts, the abnormal scrap rate is very small, and the maintenance cost is very low. (5) Flexible application: small size, flat packaging, easy to develop into light, thin, short products, can be made into various forms of dot, line, surface special products. (6) Green environmental protection: waste can be recycled without pollution, major Plant light And unlike high-pressure mercury lamps, they contain mercury. (7) Very short response time: energy-saving ceiling lamp suitable for frequent switching and high-frequency operation.
one major Plant light The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Plant light The use of crystal oscillator time control can make the time control more accurate.
fixed major Plant light There are many methods, such as ceiling, embedded, hoisting (straight pipe or chain) and wall absorption. Generally, open lamps are usually used indoors. Enamel surface reflector shall be selected, with thick aluminum oxide film or aluminum reflector coated with silicon dioxide protective film. Movable local illuminators are equipped with corresponding handles, hooks, clamps, etc. Fixed local illuminators are usually firmly locked on the working machine by screws or fixing mechanisms. For large factories and large machine tool places requiring separate lighting major Plant light Reflectors made of materials with strong light control characteristics, such as prismatic glass, mirror glass and polished aluminum, to obtain narrow beam distribution.
The bulb shall be firm and upright and shall not be loose or skewed. If the enamel umbrella is corroded or deformed major Plant light It needs to be replaced in time. Before using electric tools, please check whether the wiring, plug, socket, grounding and leakage protection devices are in good condition. Do not use them if they are damaged. Safety slogans, warning signs and safety operation instruction boards shall be set up on the construction site. Materials on the site shall be stacked orderly and stably and handled from top to bottom. When using hand-held electric tools, please wear personal protective equipment and the power cord should be empty. It is forbidden for non operators to use it on site major Plant light Power switches, wires and various mechanical equipment. Outdoor construction is not allowed in rainy season. Outdoor construction should be carried out after the rain is dry. The Quality Safety Department is responsible for preparing labor protection articles to ensure the safety of construction personnel.
