The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Plant lighting It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Plant lighting The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.
one major Plant lighting The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Plant lighting The use of crystal oscillator time control can make the time control more accurate.
1. Lamp holder: it needs to be sealed through the lamp holder. major Plant lighting The waterproof treatment of lamp cap can ensure the service life of street lamp. Therefore, the selection of street lamp housing is very important. 2. Controller: when selecting, pay attention to whether the style is waterproof. When installing the controller, it is usually placed in the road to better avoid wind and sun exposure. 3. Battery: it needs to have certain waterproof performance. In order to install the battery, please bury the battery about 40cm underground to avoid flooding. After that, test major Plant lighting Head to check whether the street lamp lights up normally. If it is opened, it can be used normally; otherwise, it needs to be replaced. Light poles need to be hot-dip galvanized to ensure smooth surface, no color difference, no pinholes, and no skin peeling after use.
There are many types of LED street lights, which can be classified according to the following categories. 1 major Plant lighting Height of street lights: high pole street lights, medium pole lights, street lights, garden lights, lawn lights; 2, according to major Plant lighting Material of lamp pole: hot-dip galvanized railway lamp, steel street lamp and stainless steel street lamp; 3. Divided by shape: Chinese lamp, antique lamp, landscape lamp, single arm street lamp, double arm street lamp. 4. According to the power supply mode: urban circuit light, solar street light, wind solar complementary street light.
How to reduce the risk of theft of Shandong solar street lights? Lanyue Optoelectronics Co., Ltd. recommends that you take the following measures: (1) major Plant lighting Its cost is higher than that of traditional street lamp poles, and its anti-theft and stability technology is not mature enough. They should be installed in public places or relatively safe places in cities. It is not easy to install them in suburbs; (2) Among all the components, the battery is the part that is easy to be stolen. Therefore, we can bury the battery underground, under the building as far as possible, and then pour it in with cement, which can achieve good results. Anti-theft effect; (3) Attach importance to major Plant lighting Security monitoring, establish monitoring systems or install alarm systems in places prone to theft, timely understand the use of solar street lights, and carry out effective management;
When the solar street lamp leaves the factory, the working time is generally set according to the customer's requirements. major Plant lighting The start and stop time of is determined by the street lamp controller. Most of the controllers are installed inside the light door, while most of the lithium battery storage and control integrated machines produced by our company are installed at the bottom of the solar panel. Controller adjustment is divided into manual adjustment and remote control adjustment. The external adjustment button can be adjusted manually. However, most of the current markets are remote control adjustment. This type of controller needs to be equipped with a remote control to adjust the working time. How to adjust major Plant lighting The time of also depends on the type of controller used.
