1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Mining lamp Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Mining lamp Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Mining lamp The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Mining lamp The general trend of. There is a lot to do.

(1) There are potential safety hazards in municipal lighting: due to the construction quality, garden engineering transformation, aging materials, abnormal power supply, water and electricity pipeline conflict, many potential safety hazards have been brought. (2) Solar street lamps are energy-saving and environment-friendly new energy power generation products. There is no electricity bill. High electricity charge for mains lighting: major Mining lamp Our jobs have fixed and high electricity bills. Solar lighting is free of electricity charge: solar road lighting is a one-time investment without any maintenance costs, the investment cost can be recovered within three years, and has long-term benefits. （3） major Mining lamp The installation of the solar street lamp is very simple: when installing the solar street lamp, you don't need to lay complex lines, just make a cement base and fix it with stainless steel screws. The installation of municipal lighting fixtures is very complicated: there are complex operating procedures in the municipal lighting project.

1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Mining lamp Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Mining lamp manufactor Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

Considering that street lamps are conductors, one way is major Mining lamp Combination of external lightning protection and internal lightning protection. As the material of street lamp is conductor, it is equivalent to lightning rod, and downlead and grounding grid need to be installed in the design. These systems constitute the external lightning protection system. After the completion of the external lightning protection system, the fire and personal safety accidents caused by the direct lightning stroke of the street lamp can be avoided. After the completion of external lightning protection, the internal lightning protection system can protect the equipment by grounding and setting voltage protection. major Mining lamp The internal lightning protection system is ready to prevent induced lightning and other forms of overvoltage intrusion, which may damage the power supply. This is also beyond the protection of external lightning protection system. Therefore, the built-in internal protection and external protection can complement each other.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Mining lamp Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Mining lamp To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.