The bulb shall be firm and upright and shall not be loose or skewed. If the enamel umbrella is corroded or deformed major Intelligent factory lighting It needs to be replaced in time. Before using electric tools, please check whether the wiring, plug, socket, grounding and leakage protection devices are in good condition. Do not use them if they are damaged. Safety slogans, warning signs and safety operation instruction boards shall be set up on the construction site. Materials on the site shall be stacked orderly and stably and handled from top to bottom. When using hand-held electric tools, please wear personal protective equipment and the power cord should be empty. It is forbidden for non operators to use it on site major Intelligent factory lighting Power switches, wires and various mechanical equipment. Outdoor construction is not allowed in rainy season. Outdoor construction should be carried out after the rain is dry. The Quality Safety Department is responsible for preparing labor protection articles to ensure the safety of construction personnel.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Intelligent factory lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Intelligent factory lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

1. Lamp holder: it needs to be sealed through the lamp holder. major Intelligent factory lighting The waterproof treatment of lamp cap can ensure the service life of street lamp. Therefore, the selection of street lamp housing is very important. 2. Controller: when selecting, pay attention to whether the style is waterproof. When installing the controller, it is usually placed in the road to better avoid wind and sun exposure. 3. Battery: it needs to have certain waterproof performance. In order to install the battery, please bury the battery about 40cm underground to avoid flooding. After that, test major Intelligent factory lighting Head to check whether the street lamp lights up normally. If it is opened, it can be used normally; otherwise, it needs to be replaced. Light poles need to be hot-dip galvanized to ensure smooth surface, no color difference, no pinholes, and no skin peeling after use.

During use, the bulb will be hit by wind and rain, which may cause its angle deviation, thus affecting the lighting effect. If any deviation is found, it must be adjusted in time. Check the bulb surface regularly. If on major Intelligent factory lighting Cracks found on the surface glass of the bulb may cause rainwater to enter the bulb, which will seriously affect the use effect and service life of the bulb. The bulb should be removed immediately and sent to the original factory for repair. Avoid all kinds of serious accidents, such as leakage. Clean the lamp regularly to maintain its brightness. Turn off the lamp before cleaning it major Intelligent factory lighting The power supply of the lamp shall be cleaned with a dry cloth or dry cloth to prevent the lamp from being damp, let alone with chemical or corrosive substances. Otherwise, the bulb will be corroded, which may cause accidents.

1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Intelligent factory lighting Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Intelligent factory lighting Price Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

How to reduce the risk of theft of Shandong solar street lights? Lanyue Optoelectronics Co., Ltd. recommends that you take the following measures: (1) major Intelligent factory lighting Its cost is higher than that of traditional street lamp poles, and its anti-theft and stability technology is not mature enough. They should be installed in public places or relatively safe places in cities. It is not easy to install them in suburbs; (2) Among all the components, the battery is the part that is easy to be stolen. Therefore, we can bury the battery underground, under the building as far as possible, and then pour it in with cement, which can achieve good results. Anti-theft effect; (3) Attach importance to major Intelligent factory lighting Security monitoring, establish monitoring systems or install alarm systems in places prone to theft, timely understand the use of solar street lights, and carry out effective management;