When the solar street lamp leaves the factory, the working time is generally set according to the customer's requirements. major Multi function street lamp The start and stop time of is determined by the street lamp controller. Most of the controllers are installed inside the light door, while most of the lithium battery storage and control integrated machines produced by our company are installed at the bottom of the solar panel. Controller adjustment is divided into manual adjustment and remote control adjustment. The external adjustment button can be adjusted manually. However, most of the current markets are remote control adjustment. This type of controller needs to be equipped with a remote control to adjust the working time. How to adjust major Multi function street lamp The time of also depends on the type of controller used.

The working voltage of a single bulb for LED tunnel lighting is very low, about 3V, so the power consumption of a low-voltage working environment is half of the power required for the same strong light. The tunnel lamp has a long service life and does not need regular maintenance and inspection. After a period of use, the traditional major Multi function street lamp The brightness of the tunnel lamp will be greatly reduced, but its attenuation is only 20% of that of the tunnel lamp. Moreover, the tunnel lamp is small in size and can be made into various shapes to adapt to various environments. The shell of the tunnel lamp is of integrated design, which is durable and not easy to be damaged. Each light source inside can be installed and removed separately, which is very convenient in the future maintenance process, and the overall design can ensure good heat dissipation effect. The heat dissipation rack inside the shell, the airflow and the heat emitted by the full contact with the air, effectively reduce the major Multi function street lamp And prolongs the service life of the tunnel lamp.

Main pole of high pole lamp: major Multi function street lamp When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Multi function street lamp If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.

one major Multi function street lamp The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Multi function street lamp The use of crystal oscillator time control can make the time control more accurate.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Multi function street lamp Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Multi function street lamp Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.