1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Intelligent factory lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Intelligent factory lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.
(1) High light efficiency: the spectrum is almost all concentrated on the visible light frequency, and the efficiency can reach 80% - 90%. (2) High light quality: because there is no ultraviolet and infrared ray in the spectrum, there is no heat and radiation. This is a typical green light source. (3) Long life: the standard life is 40000 hours when the luminous flux decays to 70%. major Intelligent factory lighting It can be used for 8 years under normal conditions. (4) Reliable and durable: there is no tungsten wire, glass and other easily damaged parts, the abnormal scrap rate is very small, and the maintenance cost is very low. (5) Flexible application: small size, flat packaging, easy to develop into light, thin, short products, can be made into various forms of dot, line, surface special products. (6) Green environmental protection: waste can be recycled without pollution, major Intelligent factory lighting And unlike high-pressure mercury lamps, they contain mercury. (7) Very short response time: energy-saving ceiling lamp suitable for frequent switching and high-frequency operation.
1. Selection of lamp type: reasonable lamps shall be selected for solar garden lamps. Attention should be paid to determining the light distribution type of the lamp according to the function, size and shape of the garden. 2. Pay attention to the lighting effect of lamps: major Intelligent factory lighting Pay attention to the efficiency of lamps. 3. Attention should be paid to the selection of lamps that are easy to maintain: the daily maintenance of solar garden lamps is a troublesome thing, so we should pay attention to the selection of lamps that are easy to maintain and are not prone to operating problems. 4. Pay attention to special places: some parks have special environment. When high temperature parts such as lamps and lamp accessories are close to combustibles, fire prevention measures such as heat insulation and heat dissipation shall be taken; 5. Pay attention to the appearance of lamps: major Intelligent factory lighting The appearance of the solar garden lamp is in harmony with the courtyard environment, and cannot be placed in an inappropriate place.
The life of LED mining lamp depends largely on the level of heat dissipation, and the main way to improve the level of heat dissipation is to transfer the excess heat generated by the chip through the radiator and radiator. At the same time, major Intelligent factory lighting The main parameters related to LED heat dissipation are thermal resistance, junction temperature, temperature rise, etc. Thermal resistance is the quotient obtained by dividing the difference between the effective temperature of the equipment and the temperature of the external designated reference point by the steady-state power consumption in the equipment. It is an important parameter indicating the degree of heat dissipation of equipment. Junction temperature refers to the temperature of the semiconductor junction of the main heating part in the LED device. It reflects major Intelligent factory lighting Temperature value that can be withstood under working conditions. Temperature rise refers to the temperature rise of the enclosure environment. It refers to the difference between the temperature of LED equipment shell and the ambient temperature. This is a temperature value that can be directly measured, which can directly reflect the heat dissipation degree around LED devices.
Main pole of high pole lamp: major Intelligent factory lighting When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Intelligent factory lighting If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.
