1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Multi function street lamp Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Multi function street lamp engineering Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

(1) High light efficiency: the spectrum is almost all concentrated on the visible light frequency, and the efficiency can reach 80% - 90%. (2) High light quality: because there is no ultraviolet and infrared ray in the spectrum, there is no heat and radiation. This is a typical green light source. (3) Long life: the standard life is 40000 hours when the luminous flux decays to 70%. major Multi function street lamp It can be used for 8 years under normal conditions. (4) Reliable and durable: there is no tungsten wire, glass and other easily damaged parts, the abnormal scrap rate is very small, and the maintenance cost is very low. (5) Flexible application: small size, flat packaging, easy to develop into light, thin, short products, can be made into various forms of dot, line, surface special products. (6) Green environmental protection: waste can be recycled without pollution, major Multi function street lamp And unlike high-pressure mercury lamps, they contain mercury. (7) Very short response time: energy-saving ceiling lamp suitable for frequent switching and high-frequency operation.

1. Shandong solar street lights will not go out suddenly: solar street lights use solar energy to absorb sunlight to charge batteries. When the weather is bad, the battery will provide power for the street lamp lighting, so the lamp will not be turned off suddenly. 2. Quality of LED light source: major Multi function street lamp LED lamp cap is generally used as the light source of. Because LED lamp cap has many advantages, its lighting life is long, and it will not emit too much heat when used, which greatly extends the service life of the light source. 3. It can also be used normally in continuous rainy days: major Multi function street lamp Solar energy is used to generate electricity, so they can usually be used for lighting on days without sunshine. Solar street lamp manufacturers will also consider these issues when designing solar street lamps, and then through communication with customers, according to the local rainy weather conditions of customers, they will configure appropriate street lamp accessories to solve most local problems.

(1) Solar panel: 18v, 30-240wp monocrystalline silicon or polycrystalline silicon; (2) Controller: major Multi function street lamp Intelligent controller; (3) Battery: DC12V, 24V, lead-acid battery or gel battery, maintenance free; (4) Light source type: high-power LED integrated lamp head, die-casting aluminum material; (5) Light source power: 20-60W; (6) Light pole material: steel structure, hot-dip galvanizing, plastic spraying treatment; (7) Height: 6-8m; (8) Working time: 5-12 hours, 4-5 days in rainy days (different sunshine time in different regions); (9) Working temperature: - 35 ℃ - 65 ℃; In addition, major Multi function street lamp For the selection of solar panels and batteries, please refer to the purchase notes of solar street lamps. It can be seen that the selection of proper garden lamps is not only reasonable in price, but also comprehensive. In order to avoid unnecessary troubles.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Multi function street lamp It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. The installation position of the floodlight shall be able to bear the weight of the floodlight, and its bearing capacity shall be greater than major Multi function street lamp 10 times the weight, so that the lamp can be firmly installed and avoid the risk of falling in the future.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Multi function street lamp Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Multi function street lamp Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.