The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Plant light It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Plant light Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.

(1) There are potential safety hazards in municipal lighting: due to the construction quality, garden engineering transformation, aging materials, abnormal power supply, water and electricity pipeline conflict, many potential safety hazards have been brought. (2) Solar street lamps are energy-saving and environment-friendly new energy power generation products. There is no electricity bill. High electricity charge for mains lighting: major Plant light Our jobs have fixed and high electricity bills. Solar lighting is free of electricity charge: solar road lighting is a one-time investment without any maintenance costs, the investment cost can be recovered within three years, and has long-term benefits. （3） major Plant light The installation of the solar street lamp is very simple: when installing the solar street lamp, you don't need to lay complex lines, just make a cement base and fix it with stainless steel screws. The installation of municipal lighting fixtures is very complicated: there are complex operating procedures in the municipal lighting project.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Plant light It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Plant light The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.

1. Lamp holder: it needs to be sealed through the lamp holder. major Plant light The waterproof treatment of lamp cap can ensure the service life of street lamp. Therefore, the selection of street lamp housing is very important. 2. Controller: when selecting, pay attention to whether the style is waterproof. When installing the controller, it is usually placed in the road to better avoid wind and sun exposure. 3. Battery: it needs to have certain waterproof performance. In order to install the battery, please bury the battery about 40cm underground to avoid flooding. After that, test major Plant light Head to check whether the street lamp lights up normally. If it is opened, it can be used normally; otherwise, it needs to be replaced. Light poles need to be hot-dip galvanized to ensure smooth surface, no color difference, no pinholes, and no skin peeling after use.

1. Strong anti-static capability: LED with strong anti-static capability has a long service life. 2. Brightness: The price of LED varies with its brightness. 3. Wavelength: LEDs with the same wavelength and color are expensive. 4. Luminescence viewpoint: LEDs for different purposes have different luminescence viewpoints. 5. LED chip: major Plant light The illuminant of is a chip, and the price of different chips varies greatly. 7. Colloid: Generally, the colloid of LED is epoxy resin. LEDs with UV resistance and flame retardancy are more expensive. 8. Chip size: the chip size is represented by the side length. Big chip major Plant light Its quality is better than that of small chips. The price is proportional to the chip size. 9. Radiator: The radiator can see the appearance of the lamp. Temperature will affect the life of LED lamp beads. Counting plays a vital role. 10. Power supply: According to the plan requirements of different manufacturers, it can be divided into two types: constant current power supply and constant voltage power supply.