Like the hump of a camel, the battery of a solar street lamp has the function of storing energy. The importance is self-evident. Third generation solar street lamp battery replacement, from lead-acid battery to gel battery to lithium battery. At present, the mainstream major Cast light Battery has gradually developed from gel battery to lithium battery. Relatively speaking, colloidal battery has low price, relatively mature technology and high stability. advantage. The disadvantages are that compared with lithium batteries of the same level, the service life is relatively short, the electric energy storage capacity of the same volume is less, and there are other fatal disadvantages. Although the apparent price is a little expensive, the use cost is very low. Two years of poor use, we major Cast light manufactor The battery pack can be used for 8-10 years. Welcome new and old customers to call and write.

1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Cast light Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Cast light manufactor Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Cast light Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Cast light It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.

First, we need to observe major Cast light The workmanship of the mask and its luminous effect. This depends on how much light the bulb lamp shade emits to the light source. When viewing the mask, you can view its shape, whether the light transmittance and thickness of the bulb are the same, and check the approximate blur of the mask. We need to see if the material of the bulb is suitable for heat conduction. You can test in the field. After working for several minutes, observe whether there is odor above the bulb when the temperature rises. After that, we will also check the lamp body temperature after the power is turned off. The lower the temperature, the better. ordinary major Cast light It will change due to the change of ambient temperature. When selecting bulb lamp, you need to check its color temperature. Generally speaking, the color temperature should not be too high or too low as long as it can meet the normal household lighting needs.

(1) Solar panel: 18v, 30-240wp monocrystalline silicon or polycrystalline silicon; (2) Controller: major Cast light Intelligent controller; (3) Battery: DC12V, 24V, lead-acid battery or gel battery, maintenance free; (4) Light source type: high-power LED integrated lamp head, die-casting aluminum material; (5) Light source power: 20-60W; (6) Light pole material: steel structure, hot-dip galvanizing, plastic spraying treatment; (7) Height: 6-8m; (8) Working time: 5-12 hours, 4-5 days in rainy days (different sunshine time in different regions); (9) Working temperature: - 35 ℃ - 65 ℃; In addition, major Cast light For the selection of solar panels and batteries, please refer to the purchase notes of solar street lamps. It can be seen that the selection of proper garden lamps is not only reasonable in price, but also comprehensive. In order to avoid unnecessary troubles.

There are many types of LED street lights, which can be classified according to the following categories. 1 major Cast light Height of street lights: high pole street lights, medium pole lights, street lights, garden lights, lawn lights; 2, according to major Cast light Material of lamp pole: hot-dip galvanized railway lamp, steel street lamp and stainless steel street lamp; 3. Divided by shape: Chinese lamp, antique lamp, landscape lamp, single arm street lamp, double arm street lamp. 4. According to the power supply mode: urban circuit light, solar street light, wind solar complementary street light.