The life of LED mining lamp depends largely on the level of heat dissipation, and the main way to improve the level of heat dissipation is to transfer the excess heat generated by the chip through the radiator and radiator. At the same time, major Rural lighting The main parameters related to LED heat dissipation are thermal resistance, junction temperature, temperature rise, etc. Thermal resistance is the quotient obtained by dividing the difference between the effective temperature of the equipment and the temperature of the external designated reference point by the steady-state power consumption in the equipment. It is an important parameter indicating the degree of heat dissipation of equipment. Junction temperature refers to the temperature of the semiconductor junction of the main heating part in the LED device. It reflects major Rural lighting Temperature value that can be withstood under working conditions. Temperature rise refers to the temperature rise of the enclosure environment. It refers to the difference between the temperature of LED equipment shell and the ambient temperature. This is a temperature value that can be directly measured, which can directly reflect the heat dissipation degree around LED devices.

1. Lamp holder: it needs to be sealed through the lamp holder. major Rural lighting The waterproof treatment of lamp cap can ensure the service life of street lamp. Therefore, the selection of street lamp housing is very important. 2. Controller: when selecting, pay attention to whether the style is waterproof. When installing the controller, it is usually placed in the road to better avoid wind and sun exposure. 3. Battery: it needs to have certain waterproof performance. In order to install the battery, please bury the battery about 40cm underground to avoid flooding. After that, test major Rural lighting Head to check whether the street lamp lights up normally. If it is opened, it can be used normally; otherwise, it needs to be replaced. Light poles need to be hot-dip galvanized to ensure smooth surface, no color difference, no pinholes, and no skin peeling after use.

1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Rural lighting The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Rural lighting The general trend of. There is a lot to do.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Rural lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Rural lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.

The working voltage of a single bulb for LED tunnel lighting is very low, about 3V, so the power consumption of a low-voltage working environment is half of the power required for the same strong light. The tunnel lamp has a long service life and does not need regular maintenance and inspection. After a period of use, the traditional major Rural lighting The brightness of the tunnel lamp will be greatly reduced, but its attenuation is only 20% of that of the tunnel lamp. Moreover, the tunnel lamp is small in size and can be made into various shapes to adapt to various environments. The shell of the tunnel lamp is of integrated design, which is durable and not easy to be damaged. Each light source inside can be installed and removed separately, which is very convenient in the future maintenance process, and the overall design can ensure good heat dissipation effect. The heat dissipation rack inside the shell, the airflow and the heat emitted by the full contact with the air, effectively reduce the major Rural lighting And prolongs the service life of the tunnel lamp.

1: Environment friendly lamp. LED products do not contain lead and other harmful substances, and the shell can also be recycled, which is harmless to the environment. 2: Fever is low. No UV, 3: no noise. LED light will not produce noise, so it is a good choice for occasions where quasi dense electronic instruments are used. 4: Protect eyes. major Rural lighting LED constant current operation can effectively reduce LED light attenuation, start quickly, no flicker and protect eyes. 5: There is no trouble of mosquitoes, no harmful substances such as mercury, and less heat generated. 6: Wide voltage range. LED lights can be lit within a certain voltage range. 7: Power saving and long service life. It can be used for a long time without replacement, which reduces the labor cost. 8: Firm and reliable. major Rural lighting It uses epoxy resin instead of traditional glass. 9: The appearance and size of multi-functional LED lamps are the same as those of traditional fluorescent lamps, which can replace traditional fluorescent lamps. 10: Rich color makes full use of the rich color of LED to make a variety of light emitting colors.