(1) There are potential safety hazards in municipal lighting: due to the construction quality, garden engineering transformation, aging materials, abnormal power supply, water and electricity pipeline conflict, many potential safety hazards have been brought. (2) Solar street lamps are energy-saving and environment-friendly new energy power generation products. There is no electricity bill. High electricity charge for mains lighting: major Rural lighting Our jobs have fixed and high electricity bills. Solar lighting is free of electricity charge: solar road lighting is a one-time investment without any maintenance costs, the investment cost can be recovered within three years, and has long-term benefits. （3） major Rural lighting The installation of the solar street lamp is very simple: when installing the solar street lamp, you don't need to lay complex lines, just make a cement base and fix it with stainless steel screws. The installation of municipal lighting fixtures is very complicated: there are complex operating procedures in the municipal lighting project.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Rural lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Rural lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Rural lighting It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Rural lighting Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.

1. Energy saving economy. First, each solar street lamp is a relatively independent system. In the process of installation and construction, there is no need to lay cables or dig roads, thus saving a lot of manpower, material resources and installation costs; In addition, it also consumes electricity, and ordinary street lights are on all day. The lamp lasts about 6 hours, consumes about 2 kWh, and the annual electricity charge is more than 300 yuan. According to 300 street lights in the urban area, the annual cost is nearly 100000 yuan. Can be saved major Rural lighting 。 2. Energy conservation and environmental protection. Zibo major Rural lighting It is mainly composed of four departments: photovoltaic module, light-emitting diode, solar cell and controller. Photovoltaic modules absorb light in the daytime, convert solar energy into electric energy, store it in solar cells, and release illumination when it turns dark at night.

one major Rural lighting The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Rural lighting The use of crystal oscillator time control can make the time control more accurate.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Rural lighting It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Rural lighting The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.