If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Plant lighting The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Plant lighting The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Plant lighting It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Plant lighting The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Plant lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Plant lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.

LED panel light is a point shaped illuminant, which brings creative visual effects through the flexible design of points, lines and surfaces. It is light and thin, and can be installed on the ceiling, wall and the surface of the installation body, and suspended under the ceiling or the installation body. According to customer requirements, we can design light sources with different shapes and particles, which are flexible in design. High brightness major Plant lighting Light source, quick start, natural and soft light. It belongs to the category of lamps with strong anti vibration ability. The light source is a high hardness resin illuminant rather than tungsten glass, which is not easy to be damaged. Therefore, it has high anti vibration ability and strong adaptability to ambient temperature. major Plant lighting The uniform luminous reflective plate and sealed internal design are adopted, which are combined with the light guide plate and made of aluminum alloy materials. The effect is uniform and the lighting range is larger.

At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Plant lighting Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Plant lighting It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.

(1) Recommended installation height of 50W LED energy-saving mining lamp: 3-5 meters; Installation distance: 5-8m. (2) Recommended installation height of 100W LED energy-saving mining lamp: 6-8m; Installation distance: 8-10 m. (3) 120W LED energy-saving mining lamp Recommended installation height: 8-10m; Installation distance: 8-10 m. （4）150W major Plant lighting Recommended installation height: 10-15m; Installation distance: 8-12m. （5） major Plant lighting 200W Recommended installation height: 10-15m; Installation distance: 10-15m. (6) LED energy-saving mining lamp 300W recommended installation height: 15-20m; Installation distance: 20-25m. (7) Recommended installation height of 450W LED energy-saving mining lamp: 15-20m; Installation distance: 25-30m