1. Be able to monitor the temperature of the light source chip pad of the street lamp itself or the temperature of the lamp shell and conduct fault diagnosis; 2. Remote measurement of electrical parameters such as street lamp current and voltage, remote switching of street lamps, remote viewing of on-site operation of important road sections, etc; 3. According to major Industrial lighting The monitoring data of can timely grasp the abnormal position and reason of street lights, and carry out purposeful maintenance without having to go to the whole city for inspection, which speeds up the speed. 4. It has daylight sensor or on-board sensor dimming, energy saving control, time control and even RTC dimming; 5. In some areas with few people and vehicles, it can be controlled at half bright time in the middle of the night, but when people and cars pass by, major Industrial lighting They will reach the distance ahead and in a few cases restore the original brightness. Seconds. 6. The lighting standard level of the same road will change with time and traffic flow.

The working voltage of a single bulb for LED tunnel lighting is very low, about 3V, so the power consumption of a low-voltage working environment is half of the power required for the same strong light. The tunnel lamp has a long service life and does not need regular maintenance and inspection. After a period of use, the traditional major Industrial lighting The brightness of the tunnel lamp will be greatly reduced, but its attenuation is only 20% of that of the tunnel lamp. Moreover, the tunnel lamp is small in size and can be made into various shapes to adapt to various environments. The shell of the tunnel lamp is of integrated design, which is durable and not easy to be damaged. Each light source inside can be installed and removed separately, which is very convenient in the future maintenance process, and the overall design can ensure good heat dissipation effect. The heat dissipation rack inside the shell, the airflow and the heat emitted by the full contact with the air, effectively reduce the major Industrial lighting And prolongs the service life of the tunnel lamp.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Industrial lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Industrial lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Industrial lighting The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Industrial lighting The general trend of. There is a lot to do.

1. Selection of lamp type: reasonable lamps shall be selected for solar garden lamps. Attention should be paid to determining the light distribution type of the lamp according to the function, size and shape of the garden. 2. Pay attention to the lighting effect of lamps: major Industrial lighting Pay attention to the efficiency of lamps. 3. Attention should be paid to the selection of lamps that are easy to maintain: the daily maintenance of solar garden lamps is a troublesome thing, so we should pay attention to the selection of lamps that are easy to maintain and are not prone to operating problems. 4. Pay attention to special places: some parks have special environment. When high temperature parts such as lamps and lamp accessories are close to combustibles, fire prevention measures such as heat insulation and heat dissipation shall be taken; 5. Pay attention to the appearance of lamps: major Industrial lighting The appearance of the solar garden lamp is in harmony with the courtyard environment, and cannot be placed in an inappropriate place.