Main pole of high pole lamp: major Industrial lighting When the height of the main pole exceeds 20m, the steel plate with a wall thickness of 5.6mm is usually used as the main material. After the overall welding of the high pole lamp, the internal and external surface layers need to be hot-dip galvanized and qualified galvanized. This process can ensure that the main pole will not rust for 15 years. Lifting system: the lifting system is regarded as the core part of the high pole lamp. The landing action of the light panel depends entirely on the landing system. The landing system of high pole lamp is mainly hoist and wire rope. First, install the elevator on the main rod. Weathering and rain will not cause line aging. Secondly, the hoist seldom starts. If major Industrial lighting If the light source has not been damaged in ten years, it will not need to be touched in ten years. Lamp cap: Whether it is LED lamp cap or low pressure sodium lamp, the light source is the main symbol of the whole set of high pole lamp. If the light source is broken and the high pole lamp is broken, the selection of light source quality is particularly important.

1. Be able to monitor the temperature of the light source chip pad of the street lamp itself or the temperature of the lamp shell and conduct fault diagnosis; 2. Remote measurement of electrical parameters such as street lamp current and voltage, remote switching of street lamps, remote viewing of on-site operation of important road sections, etc; 3. According to major Industrial lighting The monitoring data of can timely grasp the abnormal position and reason of street lights, and carry out purposeful maintenance without having to go to the whole city for inspection, which speeds up the speed. 4. It has daylight sensor or on-board sensor dimming, energy saving control, time control and even RTC dimming; 5. In some areas with few people and vehicles, it can be controlled at half bright time in the middle of the night, but when people and cars pass by, major Industrial lighting They will reach the distance ahead and in a few cases restore the original brightness. Seconds. 6. The lighting standard level of the same road will change with time and traffic flow.

First, we need to observe major Industrial lighting The workmanship of the mask and its luminous effect. This depends on how much light the bulb lamp shade emits to the light source. When viewing the mask, you can view its shape, whether the light transmittance and thickness of the bulb are the same, and check the approximate blur of the mask. We need to see if the material of the bulb is suitable for heat conduction. You can test in the field. After working for several minutes, observe whether there is odor above the bulb when the temperature rises. After that, we will also check the lamp body temperature after the power is turned off. The lower the temperature, the better. ordinary major Industrial lighting It will change due to the change of ambient temperature. When selecting bulb lamp, you need to check its color temperature. Generally speaking, the color temperature should not be too high or too low as long as it can meet the normal household lighting needs.

The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Industrial lighting It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Industrial lighting Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.

1. High purity aluminum reflector, accurate beam and good reflection effect. 2. Symmetrical narrow angle, wide angle and asymmetric light distribution system. 3. The rear open bulb can be replaced, which is easy to maintain. 4. The lamp is equipped with a dial to adjust the lighting angle. major Industrial lighting Controlled by the built-in microchip. In small engineering applications, it can be used without a controller, and can achieve gradual change, jump, color flicker, random flicker. DMX can also control dynamic effects such as gradients to achieve effects such as chasing and scanning. Its main application places may be: single building, exterior wall lighting of historical buildings, interior and exterior lighting of buildings, interior local lighting, green landscape lighting, billboard lighting, medical culture and other professional facilities lighting, bars, dance halls and other entertainment places major Industrial lighting 。