1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Plant lighting Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Plant lighting Price Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

one major Plant lighting The charging circuit adopts a dual MOS series control circuit, which can reduce the voltage loss of the circuit by nearly half compared with the use of diodes. The use of PWM energy-saving control greatly increases the power consumption. 2. The load mode adopts pure light control. When the light is dark, the light sensor system will automatically light up. 3. Scientific battery management method. When over discharge occurs, the battery voltage will promote charging. After maintenance and compensation, it can be used normally. Direct charging and floating charging are used to connect rechargeable batteries. 4. All restrictions of all industrial chips and closed components can operate normally in cold, high temperature and humid environments. At the same time, major Plant lighting The use of crystal oscillator time control can make the time control more accurate.

1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Plant lighting The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Plant lighting The general trend of. There is a lot to do.

1、 Disconnection. For "dead light", we should first determine major Plant lighting Is it short circuit or open circuit. 2、 The adhesive layer is peeled off. For some LED energy-saving project lights with vertical chips, the common reasons for dead lights are the peeling off of the bottom of the chip bonding layer and the peeling off of the bracket coating. 3、 The welding spot is burnt. In some cases, the dead light of the bulb may not be caused by the bulb itself, but also by the power supply used. 4、 Chip corrosion. The previous energy-saving floodlights and energy-saving floodlights are open circuit. The following is the condition of short circuit dead light. major Plant lighting There are many reasons for dead lights. Dead light may appear in every link from packaging, application to use.

In order to better serve customers, the two companies will share the following technologies with each other. Shandong Qihang Electric Co., Ltd. will share the advantages of workshop, street lamp production technology, street lamp twelve phase, solar street lamp technology and street lamp cap technology. Shandong Lanyue Photoelectric Technology Co., Ltd major Plant lighting Six phase and other related technologies of flood lights, tunnel lights and other indoor and landscape lights. In order to safeguard the interests of customers, the two companies will communicate with each other in the market. Qihang Electric will share factory customers, while Lanyue Optoelectronics Co., Ltd. will share municipal users. After communication, Qihang Electric will use its own municipal street lights and solar street lights. Technical advantages such as intelligent lighting equipment provide outdoor lighting technical services for customers of Lanyue Optoelectronics, and Lanyue Optoelectronics provides outdoor lighting technical services for customers of Shandong Qihang Electric Co., Ltd major Plant lighting , high ceiling lamps and other indoor and engineering lighting products and other technical advantages.

1. Lamp holder: it needs to be sealed through the lamp holder. major Plant lighting The waterproof treatment of lamp cap can ensure the service life of street lamp. Therefore, the selection of street lamp housing is very important. 2. Controller: when selecting, pay attention to whether the style is waterproof. When installing the controller, it is usually placed in the road to better avoid wind and sun exposure. 3. Battery: it needs to have certain waterproof performance. In order to install the battery, please bury the battery about 40cm underground to avoid flooding. After that, test major Plant lighting Head to check whether the street lamp lights up normally. If it is opened, it can be used normally; otherwise, it needs to be replaced. Light poles need to be hot-dip galvanized to ensure smooth surface, no color difference, no pinholes, and no skin peeling after use.