major Street lamp high pole lamp Corresponding rules and regulations shall be formulated for construction, and construction personnel shall strictly abide by the rules and regulations. Follow the instructions of the on-site construction personnel and complete the production tasks together. Expressway safety slogans, warning signs, etc. shall be set around the buildings, and shall not be removed or moved at will. Their movement shall be approved by the on-site construction director. The installation height of lamps shall be consistent. Install according to the design requirements. major Street lamp high pole lamp The height of should be equal to the width of the road to be lit. Bench drills, toothless saws, cutting machines, etc., as well as electric tools for processing, need to be equipped with leakage protection devices. The elevation angle of the lamp is determined by the street width and light distribution curve of the lamp, and the elevation angle of each lamp needs to be the same. The place where resin glue and paint are stored shall be far away from fire sources, and sufficient fire-fighting equipment shall be placed.

At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Street lamp high pole lamp Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Street lamp high pole lamp It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.

With the emergence of high brightness white LED light source, it is possible to apply it in the lighting field. According to the prediction of international authoritative organizations, the 21st century will enter the era of new light sources represented by LED, that is, the fourth generation of new light sources. major Street lamp high pole lamp Its brightness is the same as that of traditional fluorescent lamps, and its color is gentle and easy to accept. The service life is 50000-80000 hours. When the bulb is started, it will open immediately and can be repaired when it is damaged (the traditional fluorescent lamp has been damaged and cannot be reused). It is not only very energy-saving, but also more environmentally friendly. major Street lamp high pole lamp It is one of the main products promoted by the national green lighting energy-saving project, and is currently the first choice to replace the traditional high-pressure sodium lamp for industrial and mining lamps. At present, LED mining lamp has been used in many industrial enterprises, and its application effect is well received by customers.

Computer modeling is used to simulate the luminous angle of the reflector light source and the spatial structure of the LED reflector, track the refraction track of light, and adjust the curvature of the reflector to achieve the light intensity distribution of the reflector The functional requirements of the LED light beam angle are greatly improved major Street lamp high pole lamp The light efficiency of the reflector reduces the possibility of astigmatism and glare. The reflective surface can be plated with orange peel and smooth. It can be more uniform and soft, without black holes, yellow circles. High reflection efficiency, no layering, high temperature resistance. The frosted mirror gently reflects light, which is suitable for occasions with weak light such as supermarkets and shopping centers. major Street lamp high pole lamp It is not applicable to places with high illumination requirements such as industries and stadiums. If it is used for industrial lighting, it needs a reflector with high refraction and luminous efficiency, and when the light passes through the reflector, it must reduce the light loss.

fixed major Street lamp high pole lamp There are many methods, such as ceiling, embedded, hoisting (straight pipe or chain) and wall absorption. Generally, open lamps are usually used indoors. Enamel surface reflector shall be selected, with thick aluminum oxide film or aluminum reflector coated with silicon dioxide protective film. Movable local illuminators are equipped with corresponding handles, hooks, clamps, etc. Fixed local illuminators are usually firmly locked on the working machine by screws or fixing mechanisms. For large factories and large machine tool places requiring separate lighting major Street lamp high pole lamp Reflectors made of materials with strong light control characteristics, such as prismatic glass, mirror glass and polished aluminum, to obtain narrow beam distribution.