At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Municipal lighting Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Municipal lighting It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.
LED garden lights are energy-saving and environmentally friendly. The main structure is an electroluminescent semiconductor diode, which has low luminous flux loss and long service life. According to the scientific research results of LED light source, major Municipal lighting Its service life is three times that of the basic light source and 30% that of the energy-saving street lamp. Power saving is equal to saving the investment in electricity costs, and it is also because LED courtyard lamps have their unique advantages, which can meet the requirements of today's society for energy conservation and environmental protection. courtyard major Municipal lighting The advantage of saving more electricity costs has a wide influence on the market. In order to improve people's quality of life, the street lamps that need to be used are energy-saving and environmentally friendly. Both specifications, lighting performance and lighting effect can meet the requirements of street lamp standards. Facing many LED garden lights with complex market environment, it is necessary to choose a good brand LED garden light manufacturer.
The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Municipal lighting It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Municipal lighting Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.
1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Municipal lighting The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Municipal lighting The general trend of. There is a lot to do.
If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Municipal lighting The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Municipal lighting The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.
1. Be able to monitor the temperature of the light source chip pad of the street lamp itself or the temperature of the lamp shell and conduct fault diagnosis; 2. Remote measurement of electrical parameters such as street lamp current and voltage, remote switching of street lamps, remote viewing of on-site operation of important road sections, etc; 3. According to major Municipal lighting The monitoring data of can timely grasp the abnormal position and reason of street lights, and carry out purposeful maintenance without having to go to the whole city for inspection, which speeds up the speed. 4. It has daylight sensor or on-board sensor dimming, energy saving control, time control and even RTC dimming; 5. In some areas with few people and vehicles, it can be controlled at half bright time in the middle of the night, but when people and cars pass by, major Municipal lighting They will reach the distance ahead and in a few cases restore the original brightness. Seconds. 6. The lighting standard level of the same road will change with time and traffic flow.
