The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Solar street lamp It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Solar street lamp The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.
install major Solar street lamp The construction site shall be provided with safety slogans, warning signs and safety operation instruction boards, which shall not be removed or moved at will. Any movement shall be approved by the person in charge of site construction. When working on site, please pay attention to vehicle access and mechanical lifting. During normal construction, there should be no less than 2 people, and when there is only one person on site, no operation is allowed. Obey the instructions of on-site construction personnel, obey the assignment, unite and complete the production task. Materials on site shall be stacked neatly, and hazardous materials, chemical reagents and flammable materials must be placed separately. It is strictly prohibited to work in flammable and explosive places, open fire, smoking, etc. In operation major Solar street lamp Before that, please check whether the operation site is safe, whether the road is unblocked and whether the protective measures are complete. The tools used should be restored after the work is completed. Please wear safety belt when working at heights, cliffs and steep slopes without protective facilities.
At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Solar street lamp Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Solar street lamp It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.
If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Solar street lamp The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Solar street lamp The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.
The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Solar street lamp It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. The installation position of the floodlight shall be able to bear the weight of the floodlight, and its bearing capacity shall be greater than major Solar street lamp 10 times the weight, so that the lamp can be firmly installed and avoid the risk of falling in the future.
Using the integrated technology of LED electro-optic source, according to major Solar street lamp The characteristics of semiconductor luminescence, ingenious circuit design and unique lighting geometric appearance, major Solar street lamp It can save more than 80% of electricity, realizing effective energy saving. The ultra long service life is up to 50000 hours, which can be used well in various special environments (such as low temperature and high temperature conditions). It solves the problems of low power and insufficient brightness of semiconductor electric light source in the lighting field, and shows excellent high brightness characteristics. There is no need for ballast, no starting difficulty, complete overcurrent, overvoltage, short circuit, temperature, surge protection, and its lighting optical performance is brighter and more complete than 75W/400W/1000W metal halide lamp.
