If there is a problem with the solar street lamp in the countryside, first check whether the photocell is correctly connected, whether the wiring position is in poor contact, and then check whether the battery connection is correct and whether the battery voltage is normal. If the battery is excessively discharged, a fault will occur and it will automatically recover after being fully charged. Among them, major Floodlight The stability of the controller is very important for the service life of rural solar street lights, because the role of the solar controller is to control the use major Floodlight The battery board charges and discharges the battery. When choosing a solar cell, you must choose a high stability battery to ensure the service life of the battery, because the quality of the battery will also directly affect the service life of the street lamp. It can extend the service life of the whole rural solar street lamp.

The solar street lamp is composed of six main components: solar panel, lithium battery, controller, LED lamp holder, lamp pole and ground cage; major Floodlight It is made of LED lamp holder. It consists of three parts: lamp pole and grounding cage. Since the solar street lamp uses unique solar panel, lithium battery and controller components, it can easily get rid of the tedious wiring process in the building, complete the charging process independently, and automatically turn on and off the sunshine time according to the lighting conditions, or even automatically adjust the brightness of the street lamp according to the brightness in the daytime; However, urban circuit lights cannot get rid of the independent existence of municipal electricity. Cables need to be embedded at an early stage to ensure the subsequent installation of street lights. In order to control the lighting time, major Floodlight Power distribution can only be carried out on the mains. Time control can be installed on the box, and the brightness control of lighting can only be completed by adding corresponding only equipment.

(1) Recommended installation height of 50W LED energy-saving mining lamp: 3-5 meters; Installation distance: 5-8m. (2) Recommended installation height of 100W LED energy-saving mining lamp: 6-8m; Installation distance: 8-10 m. (3) 120W LED energy-saving mining lamp Recommended installation height: 8-10m; Installation distance: 8-10 m. （4）150W major Floodlight Recommended installation height: 10-15m; Installation distance: 8-12m. （5） major Floodlight 200W Recommended installation height: 10-15m; Installation distance: 10-15m. (6) LED energy-saving mining lamp 300W recommended installation height: 15-20m; Installation distance: 20-25m. (7) Recommended installation height of 450W LED energy-saving mining lamp: 15-20m; Installation distance: 25-30m

(1) High light efficiency: the spectrum is almost all concentrated on the visible light frequency, and the efficiency can reach 80% - 90%. (2) High light quality: because there is no ultraviolet and infrared ray in the spectrum, there is no heat and radiation. This is a typical green light source. (3) Long life: the standard life is 40000 hours when the luminous flux decays to 70%. major Floodlight It can be used for 8 years under normal conditions. (4) Reliable and durable: there is no tungsten wire, glass and other easily damaged parts, the abnormal scrap rate is very small, and the maintenance cost is very low. (5) Flexible application: small size, flat packaging, easy to develop into light, thin, short products, can be made into various forms of dot, line, surface special products. (6) Green environmental protection: waste can be recycled without pollution, major Floodlight And unlike high-pressure mercury lamps, they contain mercury. (7) Very short response time: energy-saving ceiling lamp suitable for frequent switching and high-frequency operation.

1. Quality assurance, green and environmental protection, our LED lamp has a long life, low light attenuation and high brightness. They are the first choice for energy-saving transformation of factories. 2. Energy saving. The service life of Danohangpu LED products can reach 50000 hours, and the energy-saving effect is 40% - 60% of that of ordinary lamps, greatly reducing the power consumption. 3. Professional major Floodlight Plan and plan. Make a reasonable lighting configuration plan according to the width of the road and the lighting time of the area, so that you will not waste money and reasonably configure the light source. 4. Professional technical guidance and after-sales service, professional technical team major Floodlight We provide on-site technical guidance and problem solving for the installation and transformation of. Perfect after-sales service is our intimate guarantee for users. 5. From the manufacturer to the manufacturer, shorten the intermediate link, and directly solve the problem that dealers do not understand the technology and the price is slightly higher from the manufacturer's plan - product customization - product inspection - product delivery - manufacturer acceptance, and one-stop service.

First, we need to observe major Floodlight The workmanship of the mask and its luminous effect. This depends on how much light the bulb lamp shade emits to the light source. When viewing the mask, you can view its shape, whether the light transmittance and thickness of the bulb are the same, and check the approximate blur of the mask. We need to see if the material of the bulb is suitable for heat conduction. You can test in the field. After working for several minutes, observe whether there is odor above the bulb when the temperature rises. After that, we will also check the lamp body temperature after the power is turned off. The lower the temperature, the better. ordinary major Floodlight It will change due to the change of ambient temperature. When selecting bulb lamp, you need to check its color temperature. Generally speaking, the color temperature should not be too high or too low as long as it can meet the normal household lighting needs.