(1) High light efficiency: the spectrum is almost all concentrated on the visible light frequency, and the efficiency can reach 80% - 90%. (2) High light quality: because there is no ultraviolet and infrared ray in the spectrum, there is no heat and radiation. This is a typical green light source. (3) Long life: the standard life is 40000 hours when the luminous flux decays to 70%. major Industrial lighting It can be used for 8 years under normal conditions. (4) Reliable and durable: there is no tungsten wire, glass and other easily damaged parts, the abnormal scrap rate is very small, and the maintenance cost is very low. (5) Flexible application: small size, flat packaging, easy to develop into light, thin, short products, can be made into various forms of dot, line, surface special products. (6) Green environmental protection: waste can be recycled without pollution, major Industrial lighting And unlike high-pressure mercury lamps, they contain mercury. (7) Very short response time: energy-saving ceiling lamp suitable for frequent switching and high-frequency operation.

1. Strong anti-static capability: LED with strong anti-static capability has a long service life. 2. Brightness: The price of LED varies with its brightness. 3. Wavelength: LEDs with the same wavelength and color are expensive. 4. Luminescence viewpoint: LEDs for different purposes have different luminescence viewpoints. 5. LED chip: major Industrial lighting The illuminant of is a chip, and the price of different chips varies greatly. 7. Colloid: Generally, the colloid of LED is epoxy resin. LEDs with UV resistance and flame retardancy are more expensive. 8. Chip size: the chip size is represented by the side length. Big chip major Industrial lighting Its quality is better than that of small chips. The price is proportional to the chip size. 9. Radiator: The radiator can see the appearance of the lamp. Temperature will affect the life of LED lamp beads. Counting plays a vital role. 10. Power supply: According to the plan requirements of different manufacturers, it can be divided into two types: constant current power supply and constant voltage power supply.

1. Compared with traditional lamps, LED lighting has obvious energy-saving advantages. Just use major Industrial lighting The initial investment to replace traditional lamps has increased, but cost recovery can be achieved by saving electricity charges in a relatively short time. The earlier you replace it, the more you can enjoy the benefits of energy conservation. 2. The energy-saving performance of LED lighting is the choice to replace the traditional mining lamp. In the context of global energy contraction and the national conditions of governments at all levels to vigorously promote energy conservation and environmental protection, replacing traditional lamps will become major Industrial lighting The general trend of. There is a lot to do.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Industrial lighting It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. The installation position of the floodlight shall be able to bear the weight of the floodlight, and its bearing capacity shall be greater than major Industrial lighting 10 times the weight, so that the lamp can be firmly installed and avoid the risk of falling in the future.

major Industrial lighting Corresponding rules and regulations shall be formulated for construction, and construction personnel shall strictly abide by the rules and regulations. Follow the instructions of the on-site construction personnel and complete the production tasks together. Expressway safety slogans, warning signs, etc. shall be set around the buildings, and shall not be removed or moved at will. Their movement shall be approved by the on-site construction director. The installation height of lamps shall be consistent. Install according to the design requirements. major Industrial lighting The height of should be equal to the width of the road to be lit. Bench drills, toothless saws, cutting machines, etc., as well as electric tools for processing, need to be equipped with leakage protection devices. The elevation angle of the lamp is determined by the street width and light distribution curve of the lamp, and the elevation angle of each lamp needs to be the same. The place where resin glue and paint are stored shall be far away from fire sources, and sufficient fire-fighting equipment shall be placed.