The working voltage of a single bulb for LED tunnel lighting is very low, about 3V, so the power consumption of a low-voltage working environment is half of the power required for the same strong light. The tunnel lamp has a long service life and does not need regular maintenance and inspection. After a period of use, the traditional major Smart street lamp The brightness of the tunnel lamp will be greatly reduced, but its attenuation is only 20% of that of the tunnel lamp. Moreover, the tunnel lamp is small in size and can be made into various shapes to adapt to various environments. The shell of the tunnel lamp is of integrated design, which is durable and not easy to be damaged. Each light source inside can be installed and removed separately, which is very convenient in the future maintenance process, and the overall design can ensure good heat dissipation effect. The heat dissipation rack inside the shell, the airflow and the heat emitted by the full contact with the air, effectively reduce the major Smart street lamp And prolongs the service life of the tunnel lamp.

Using the integrated technology of LED electro-optic source, according to major Smart street lamp The characteristics of semiconductor luminescence, ingenious circuit design and unique lighting geometric appearance, major Smart street lamp It can save more than 80% of electricity, realizing effective energy saving. The ultra long service life is up to 50000 hours, which can be used well in various special environments (such as low temperature and high temperature conditions). It solves the problems of low power and insufficient brightness of semiconductor electric light source in the lighting field, and shows excellent high brightness characteristics. There is no need for ballast, no starting difficulty, complete overcurrent, overvoltage, short circuit, temperature, surge protection, and its lighting optical performance is brighter and more complete than 75W/400W/1000W metal halide lamp.

During use, the bulb will be hit by wind and rain, which may cause its angle deviation, thus affecting the lighting effect. If any deviation is found, it must be adjusted in time. Check the bulb surface regularly. If on major Smart street lamp Cracks found on the surface glass of the bulb may cause rainwater to enter the bulb, which will seriously affect the use effect and service life of the bulb. The bulb should be removed immediately and sent to the original factory for repair. Avoid all kinds of serious accidents, such as leakage. Clean the lamp regularly to maintain its brightness. Turn off the lamp before cleaning it major Smart street lamp The power supply of the lamp shall be cleaned with a dry cloth or dry cloth to prevent the lamp from being damp, let alone with chemical or corrosive substances. Otherwise, the bulb will be corroded, which may cause accidents.

1. Be able to monitor the temperature of the light source chip pad of the street lamp itself or the temperature of the lamp shell and conduct fault diagnosis; 2. Remote measurement of electrical parameters such as street lamp current and voltage, remote switching of street lamps, remote viewing of on-site operation of important road sections, etc; 3. According to major Smart street lamp The monitoring data of can timely grasp the abnormal position and reason of street lights, and carry out purposeful maintenance without having to go to the whole city for inspection, which speeds up the speed. 4. It has daylight sensor or on-board sensor dimming, energy saving control, time control and even RTC dimming; 5. In some areas with few people and vehicles, it can be controlled at half bright time in the middle of the night, but when people and cars pass by, major Smart street lamp They will reach the distance ahead and in a few cases restore the original brightness. Seconds. 6. The lighting standard level of the same road will change with time and traffic flow.

(1) Solar panel: 18v, 30-240wp monocrystalline silicon or polycrystalline silicon; (2) Controller: major Smart street lamp Intelligent controller; (3) Battery: DC12V, 24V, lead-acid battery or gel battery, maintenance free; (4) Light source type: high-power LED integrated lamp head, die-casting aluminum material; (5) Light source power: 20-60W; (6) Light pole material: steel structure, hot-dip galvanizing, plastic spraying treatment; (7) Height: 6-8m; (8) Working time: 5-12 hours, 4-5 days in rainy days (different sunshine time in different regions); (9) Working temperature: - 35 ℃ - 65 ℃; In addition, major Smart street lamp For the selection of solar panels and batteries, please refer to the purchase notes of solar street lamps. It can be seen that the selection of proper garden lamps is not only reasonable in price, but also comprehensive. In order to avoid unnecessary troubles.