In order to better serve customers, the two companies will share the following technologies with each other. Shandong Qihang Electric Co., Ltd. will share the advantages of workshop, street lamp production technology, street lamp twelve phase, solar street lamp technology and street lamp cap technology. Shandong Lanyue Photoelectric Technology Co., Ltd major Industrial lighting Six phase and other related technologies of flood lights, tunnel lights and other indoor and landscape lights. In order to safeguard the interests of customers, the two companies will communicate with each other in the market. Qihang Electric will share factory customers, while Lanyue Optoelectronics Co., Ltd. will share municipal users. After communication, Qihang Electric will use its own municipal street lights and solar street lights. Technical advantages such as intelligent lighting equipment provide outdoor lighting technical services for customers of Lanyue Optoelectronics, and Lanyue Optoelectronics provides outdoor lighting technical services for customers of Shandong Qihang Electric Co., Ltd major Industrial lighting , high ceiling lamps and other indoor and engineering lighting products and other technical advantages.

1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Industrial lighting Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Industrial lighting manufactor Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Industrial lighting Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Industrial lighting It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.

Like the hump of a camel, the battery of a solar street lamp has the function of storing energy. The importance is self-evident. Third generation solar street lamp battery replacement, from lead-acid battery to gel battery to lithium battery. At present, the mainstream major Industrial lighting Battery has gradually developed from gel battery to lithium battery. Relatively speaking, colloidal battery has low price, relatively mature technology and high stability. advantage. The disadvantages are that compared with lithium batteries of the same level, the service life is relatively short, the electric energy storage capacity of the same volume is less, and there are other fatal disadvantages. Although the apparent price is a little expensive, the use cost is very low. Two years of poor use, we major Industrial lighting manufactor The battery pack can be used for 8-10 years. Welcome new and old customers to call and write.

1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Industrial lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Industrial lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.