Like the hump of a camel, the battery of a solar street lamp has the function of storing energy. The importance is self-evident. Third generation solar street lamp battery replacement, from lead-acid battery to gel battery to lithium battery. At present, the mainstream major Industrial lighting Battery has gradually developed from gel battery to lithium battery. Relatively speaking, colloidal battery has low price, relatively mature technology and high stability. advantage. The disadvantages are that compared with lithium batteries of the same level, the service life is relatively short, the electric energy storage capacity of the same volume is less, and there are other fatal disadvantages. Although the apparent price is a little expensive, the use cost is very low. Two years of poor use, we major Industrial lighting manufactor The battery pack can be used for 8-10 years. Welcome new and old customers to call and write.

1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Industrial lighting Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Industrial lighting manufactor Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Industrial lighting It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Industrial lighting The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.

The ultraviolet ray of LED energy-saving lamps is not particularly strong. major Industrial lighting It will not appear after using for a period of time. It may feel particularly strong and will not produce ultraviolet light, so it will not fade, will not be disturbed by mosquitoes, and the indoor sanitation can also become clean. major Industrial lighting It can also protect our eyes well. When starting, the time is faster, so it will not flash, so it can protect the eyes. The main advantage is that it can save power and has a longer service life. This is a good and reasonable guarantee. When you use it, you don't have to worry about life problems or abnormalities, nor about the cost of replacing the bulb. Moreover, when you use it, it is relatively robust and does not worry about frequent use. This would be bad.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Industrial lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Industrial lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.