1. The installation height of LED energy-saving mining lamp is determined according to the environment, because the environment will change the reflection efficiency of the lamp. Generally, the height of LED energy-saving ceiling lamp should be more than 5 meters, and the wires should not be close to the enclosure of the ceiling. If necessary, install it. If it is less than 3m, protective measures shall be taken to prevent the vehicle from contacting it. two major Plant light Waterproof and low-temperature treatment. Select the ceiling lamp with waterproof function and waterproof transformer. The chip package of the bulb is wrapped with high temperature insulating material, which can not only be waterproof, but also prevent the bulb from being damaged at low temperature under harsh conditions. three major Plant light engineering Use flat hard copper wire to connect the main line of LED energy-saving mining lamp wiring to the lamp, install one in five rings, and connect them evenly to three phase lines according to the load balance requirements.

1、 Disconnection. For "dead light", we should first determine major Plant light Is it short circuit or open circuit. 2、 The adhesive layer is peeled off. For some LED energy-saving project lights with vertical chips, the common reasons for dead lights are the peeling off of the bottom of the chip bonding layer and the peeling off of the bracket coating. 3、 The welding spot is burnt. In some cases, the dead light of the bulb may not be caused by the bulb itself, but also by the power supply used. 4、 Chip corrosion. The previous energy-saving floodlights and energy-saving floodlights are open circuit. The following is the condition of short circuit dead light. major Plant light There are many reasons for dead lights. Dead light may appear in every link from packaging, application to use.

1. High purity aluminum reflector, accurate beam and good reflection effect. 2. Symmetrical narrow angle, wide angle and asymmetric light distribution system. 3. The rear open bulb can be replaced, which is easy to maintain. 4. The lamp is equipped with a dial to adjust the lighting angle. major Plant light Controlled by the built-in microchip. In small engineering applications, it can be used without a controller, and can achieve gradual change, jump, color flicker, random flicker. DMX can also control dynamic effects such as gradients to achieve effects such as chasing and scanning. Its main application places may be: single building, exterior wall lighting of historical buildings, interior and exterior lighting of buildings, interior local lighting, green landscape lighting, billboard lighting, medical culture and other professional facilities lighting, bars, dance halls and other entertainment places major Plant light 。

In order to better serve customers, the two companies will share the following technologies with each other. Shandong Qihang Electric Co., Ltd. will share the advantages of workshop, street lamp production technology, street lamp twelve phase, solar street lamp technology and street lamp cap technology. Shandong Lanyue Photoelectric Technology Co., Ltd major Plant light Six phase and other related technologies of flood lights, tunnel lights and other indoor and landscape lights. In order to safeguard the interests of customers, the two companies will communicate with each other in the market. Qihang Electric will share factory customers, while Lanyue Optoelectronics Co., Ltd. will share municipal users. After communication, Qihang Electric will use its own municipal street lights and solar street lights. Technical advantages such as intelligent lighting equipment provide outdoor lighting technical services for customers of Lanyue Optoelectronics, and Lanyue Optoelectronics provides outdoor lighting technical services for customers of Shandong Qihang Electric Co., Ltd major Plant light , high ceiling lamps and other indoor and engineering lighting products and other technical advantages.

At present, there are basically two kinds of sensors used for parking lot lighting. One is infrared sensor, which is relatively cheap. However, due to the height of the floor, the limitation of the metal tube and the influence of the radiation angle, the infrared sensor has a certain detection blind spot. The other is a microwave sensor, which can overcome the disadvantage of detecting corner blind areas, but the price is higher. These two sensors and major Plant light Combined, the lighting energy saving of the underground parking lot is effectively realized. When someone moves the car under the light, major Plant light It will run at full speed to meet the lighting demand. When there is no car and no car, the lamp is in a sleep state, and low power lighting of about 3W is maintained to maintain the required safety lighting. Low illumination, realizing energy saving of lighting.