1. When you buy back the LED ceiling lamp, please do not install it. Please read the label of the bulb carefully and read the installation manual, and then install and use the LED ceiling lamp according to the instructions, otherwise it may be dangerous. 2. Please be careful not to change it during cleaning and maintenance major Industrial lighting Do not replace the parts of LED ceiling lamp at will. After cleaning and maintenance, install the bulb as it is, and do not omit or install the bulb components incorrectly; 3. Maintenance is required during use major Industrial lighting To extend its service life. Wipe with dry cloth frequently, and pay attention to prevent moisture intrusion to avoid rust or long-term leakage and short circuit; Wipe as much as possible to avoid affecting light penetration.

1. Quality assurance, green and environmental protection, our LED lamp has a long life, low light attenuation and high brightness. They are the first choice for energy-saving transformation of factories. 2. Energy saving. The service life of Danohangpu LED products can reach 50000 hours, and the energy-saving effect is 40% - 60% of that of ordinary lamps, greatly reducing the power consumption. 3. Professional major Industrial lighting Plan and plan. Make a reasonable lighting configuration plan according to the width of the road and the lighting time of the area, so that you will not waste money and reasonably configure the light source. 4. Professional technical guidance and after-sales service, professional technical team major Industrial lighting We provide on-site technical guidance and problem solving for the installation and transformation of. Perfect after-sales service is our intimate guarantee for users. 5. From the manufacturer to the manufacturer, shorten the intermediate link, and directly solve the problem that dealers do not understand the technology and the price is slightly higher from the manufacturer's plan - product customization - product inspection - product delivery - manufacturer acceptance, and one-stop service.

1、 Disconnection. For "dead light", we should first determine major Industrial lighting Is it short circuit or open circuit. 2、 The adhesive layer is peeled off. For some LED energy-saving project lights with vertical chips, the common reasons for dead lights are the peeling off of the bottom of the chip bonding layer and the peeling off of the bracket coating. 3、 The welding spot is burnt. In some cases, the dead light of the bulb may not be caused by the bulb itself, but also by the power supply used. 4、 Chip corrosion. The previous energy-saving floodlights and energy-saving floodlights are open circuit. The following is the condition of short circuit dead light. major Industrial lighting There are many reasons for dead lights. Dead light may appear in every link from packaging, application to use.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Industrial lighting It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Industrial lighting The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.

1. Energy saving economy. First, each solar street lamp is a relatively independent system. In the process of installation and construction, there is no need to lay cables or dig roads, thus saving a lot of manpower, material resources and installation costs; In addition, it also consumes electricity, and ordinary street lights are on all day. The lamp lasts about 6 hours, consumes about 2 kWh, and the annual electricity charge is more than 300 yuan. According to 300 street lights in the urban area, the annual cost is nearly 100000 yuan. Can be saved major Industrial lighting 。 2. Energy conservation and environmental protection. Heze major Industrial lighting It is mainly composed of four departments: photovoltaic module, light-emitting diode, solar cell and controller. Photovoltaic modules absorb light in the daytime, convert solar energy into electric energy, store it in solar cells, and release illumination when it turns dark at night.

Like the hump of a camel, the battery of a solar street lamp has the function of storing energy. The importance is self-evident. Third generation solar street lamp battery replacement, from lead-acid battery to gel battery to lithium battery. At present, the mainstream major Industrial lighting Battery has gradually developed from gel battery to lithium battery. Relatively speaking, colloidal battery has low price, relatively mature technology and high stability. advantage. The disadvantages are that compared with lithium batteries of the same level, the service life is relatively short, the electric energy storage capacity of the same volume is less, and there are other fatal disadvantages. Although the apparent price is a little expensive, the use cost is very low. Two years of poor use, we major Industrial lighting Price The battery pack can be used for 8-10 years. Welcome new and old customers to call and write.