1. Energy saving economy. First, each solar street lamp is a relatively independent system. In the process of installation and construction, there is no need to lay cables or dig roads, thus saving a lot of manpower, material resources and installation costs; In addition, it also consumes electricity, and ordinary street lights are on all day. The lamp lasts about 6 hours, consumes about 2 kWh, and the annual electricity charge is more than 300 yuan. According to 300 street lights in the urban area, the annual cost is nearly 100000 yuan. Can be saved major Industrial lighting 。 2. Energy conservation and environmental protection. Anhui major Industrial lighting It is mainly composed of four departments: photovoltaic module, light-emitting diode, solar cell and controller. Photovoltaic modules absorb light in the daytime, convert solar energy into electric energy, store it in solar cells, and release illumination when it turns dark at night.

1、 Disconnection. For "dead light", we should first determine major Industrial lighting Is it short circuit or open circuit. 2、 The adhesive layer is peeled off. For some LED energy-saving project lights with vertical chips, the common reasons for dead lights are the peeling off of the bottom of the chip bonding layer and the peeling off of the bracket coating. 3、 The welding spot is burnt. In some cases, the dead light of the bulb may not be caused by the bulb itself, but also by the power supply used. 4、 Chip corrosion. The previous energy-saving floodlights and energy-saving floodlights are open circuit. The following is the condition of short circuit dead light. major Industrial lighting There are many reasons for dead lights. Dead light may appear in every link from packaging, application to use.

The power supply of LED project lights is high-voltage alternating current. During installation, please keep away from the place that is easy to access, and properly ground the lamps to avoid electric shock accidents. When wiring, the installation personnel shall select the appropriate power line according to the power of the bulb actually used, and separate the power supply to avoid affecting the normal use of flood lights. major Industrial lighting It is designed to be waterproof and moisture-proof, and its protection grade can reach IP65. It can withstand the test of rain, but cannot work underwater, and its protection level cannot meet the requirements of underwater work. major Industrial lighting The installation position of shall be able to bear the weight of the projection lamp, and its bearing capacity shall be 10 times greater than the weight of the projection lamp, so that the lamp can be firmly installed and the danger of falling in the future can be avoided.

1、 Good corporate culture and elite team. If you want to occupy the market in the competition of the same industry, you need to have an outstanding team. Talent introduction and corporate culture play a very important role. Market competition is team competition. The formation of an elite team needs the support of a good corporate culture. 2、 Verify the status quo and launch luxury products and flagship products. Under the current national policy, environmental protection has become the key point of national governance. Introduction of environment-friendly major Industrial lighting It has become the current development trend of all enterprises. 3、 The price of good quality and good after-sales service products depends on the quality. Only good product quality can lead to good price. As a service industry, good major Industrial lighting After sales service is also very important. If the after-sales service is good, we can retain old customers and develop new customers. As long as there are customers, there is a market for products. Quality is always one.

1. LED fluorescent lamp has high luminous efficiency, low heat generation and good color rendering. Traditional lamps generate a lot of heat energy, while LED lamps convert all electric energy into light energy, avoiding energy waste and saving energy. two major Industrial lighting Mercury free, environmentally friendly, UV free. Traditional fluorescent lamps use low-pressure mercury vapor to radiate ultraviolet light in the discharge process, so that the phosphor emits visible light. 3. LED fluorescent lamp has soft light, eye protection, no noise and quick start. Traditional fluorescent lamps use AC power, so 100-120 stroboscopic lamps are generated per second. 4. LED fluorescent lamp voltage can be adjusted from 80V to 245V. Traditional fluorescent lamps are lit by the high voltage released by the rectifier, but cannot be lit when the voltage drops. five major Industrial lighting Energy saving and power saving, long service life. The power consumption of LED fluorescent lamp is less than one third of that of traditional fluorescent lamp, and its service life is ten times of that of traditional fluorescent lamp. It can be used for a long time without replacement, thus reducing labor costs. 6. It is safe and reliable with good shockproof effect. LED lamp body is made of epoxy resin rather than traditional glass, which is more solid and reliable.

major Industrial lighting Corresponding rules and regulations shall be formulated for construction, and construction personnel shall strictly abide by the rules and regulations. Follow the instructions of the on-site construction personnel and complete the production tasks together. Expressway safety slogans, warning signs, etc. shall be set around the buildings, and shall not be removed or moved at will. Their movement shall be approved by the on-site construction director. The installation height of lamps shall be consistent. Install according to the design requirements. major Industrial lighting The height of should be equal to the width of the road to be lit. Bench drills, toothless saws, cutting machines, etc., as well as electric tools for processing, need to be equipped with leakage protection devices. The elevation angle of the lamp is determined by the street width and light distribution curve of the lamp, and the elevation angle of each lamp needs to be the same. The place where resin glue and paint are stored shall be far away from fire sources, and sufficient fire-fighting equipment shall be placed.